10
Mahr GmbH, MarSurf PS 10
Rimontaggio del supporto prismatico
sull'unità traslatrice
1. Inserire l'unità traslatrice nel supporto pri-
smatico
(9)
e spingerla avanti in modo che
il tastatore
(8)
sia al centro nella scanalatura
del supporto.
2. Stringere le due viti sul lato frontale del sup-
porto prismatico con la chiave a brugola for-
nita in dotazione (2 mm) con un momento
torcente di 0,1 Nm.
Reinserimento dell'unità traslatrice in
MarSurf PS 10 (
)
1. Capovolgere MarSurf PS 10.
2. Se presente, staccare il cavo di prolunga
(13)
dell'unità traslatrice.
Allo scopo premere i fermi sulla spina
del cavo di prolunga
(13)
.
3. Inserire la spina
(21)
nell'unità traslatrice
(cfr. fig. 4)
.
4. Inserire l'unità traslatrice nella cavità di
MarSurf PS 10.
Introdurre la spina di arresto laterale
(22)
nella
scanalatura
(22a)
e il perno di arresto
(23)
nell'apertura
(23a)
.
5. Premere la copertura zigrinata sul lato po-
steriore dell'unità traslatrice
(12)
e spingere
avanti l'unità traslatrice fino a quando si in-
nesta in posizione con un clic.
Rimozione dell'unità traslatrice da MarSurf
PS 10 (
)
1. Capovolgere MarSurf PS 10.
2. Premere sul lato frontale dell'unità traslatrice
fino a quando il perno di arresto
(23)
si sgan-
cia con un clic e la spina di arresto laterale
(22)
si trova sulla parte posteriore
(cfr. fig. 4)
.
3. Afferrare l'unità traslatrice per la protezio-
ne tastatore del supporto prismatico
(9)
ed
estrarla da MarSurf PS 10.
4. Staccare la spina
(21)
dell'unità traslatrice.
5. Collegare il cavo di prolunga
(13)
all'unità
traslatrice
(12)
e al connettore
(21)
(cfr. fig. 5)
.
La spina del cavo di prolunga
(13)
si
innesta nell'unità traslatrice.
6. Se necessario, inserire l'apparecchio di valuta-
zione nella custodia per il trasporto
(14)
(cfr.
fig. 1, in basso)
.
Rimozione del supporto prismatico dall'u-
nità traslatrice (
)
(es. per cambio tastatore,
montaggio nel prisma manuale o su un attrezzo
di fissaggio)
1. Allentare le due viti sul lato frontale del sup-
porto prismatico
(9)
con la chiave a brugola
fornita in dotazione (2 mm).
2. Spingere avanti il supporto prismatico fino
a quando tocca il tastatore, quindi estrarre
l'unità traslatrice dal supporto.
3. Sostituire il tastatore:
•
Estrarre il tastatore
(8)
dall'unità trasla-
trice.
•
Inserire con attenzione il nuovo tastatore
nel relativo alloggiamento sul lato fronta-
le dell'unità traslatrice
(12)
considerando
la disposizione delle spine.
i
Summary of Contents for MarSurf PS 10
