background image

10

Maxuum III Digital Electronic Indicator 2239028 Rev D

The Short Range Maxum III unit is capable of selecting two dig-

ital ranges. The Short Range model can select between ±0.040 

and ±0.199 in (±1.00 and ±0.199 mm) ranges. The Long 

Range model has one range of ±0.100 in (±1.99 mm) only. 

Selectable Analog Magnification

Each Maxum III unit is capable of selecting between two mini-

mum analog graduation values. An inch/metric overlay can be 

used for traditional analog display preference. The Long Range 

model can select between 0.001 and 0.0005 in (0.01 and 

0.005 mm) resolutions. The Short Range model can select 

between 0.001 and 0.0005 in (0.01 and 0.005 mm) resolutions 

for the ±0.040 in / ±1.0 mm range and between 0.0005 and 

0.0001 in (0.005 and 0.001 mm) resolutions for the ±0.0199 in 

/ ±0.199 mm range

Sleep Mode

The Maxum  III unit is designed with an auto power down fea-

ture to conserve battery life. If it senses approximately 10 min-

utes of inactivity (i.e. no spindle movement, no buttons pushed, 

no Digimatic data output request), the unit will go into a Sleep 

state. Display shows only a ‘+’ or ‘-’ sign depending on measur-

ing direction selected in setup. Unit is inactive.

OPTION: The Sleep Mode may be disabled as a factory option 

when requested at time of order. However, when using bat-

tery power the life of the battery will be reduced. This option 

is typically used with the Remote External Power option, which 

bypasses battery operation.

Summary of Contents for Maxum III

























































Reviews: