9 Radio components
34
2. Press the teach-in button on the radio window
contact.
ð
The teach-in telegram is sent. If teaching-in
was successful, the LED lights up for ap-
prox. 1 second. If transfer was faulty, the
button LED flashes briefly
3 times
.
Teaching-in an RLS RC room air control
The teach-in button is on the rear side of the RLS
RC.
1. Activate teach-in mode on the receiver fan.
ð
The LED flashes on the fan, the teach-in
mode is activated.
2. Press the RLS RC teach-in button
3 times
within 2 seconds.
ð
The teach-in telegram is sent. If teaching-in
is completed successfully, the radio icon in
the display flashes briefly
3 times
. The ra-
dio icon is then permanently visible in the
display.
ð
The LED on the receiver fan lights up for 1
second upon successful teach-in.
Teaching-in slave fan
1. Activate teach-in mode on the master (re-
ceiver fan) and a fan that is not yet taught-in
(planned slave).
ð
The LED flashes, teach-in mode is activ-
ated.
2. Switch the slave fan to the send mode To do
this, press the teach-in button on the slave fan
once.
ð
The LED on the slave lights up for a short
time and then flashes briefly
once
. The
slave fan is now in
Send-learn mode.
3. Press the teach-in button on the slave fan (>1
second) until the LED on the slave fan lights
up briefly
once
.
ð
The teach-in telegram is sent. If
teaching-
in
is completed
successfully
, the button
LED lights up once for approx. 1.5 seconds.
If transfer was faulty, the button LED
flashes briefly 3 times. If the
teach-in pro-
cess fails
the LED on the slave fan flashes
briefly
3 times
. The process has to be re-
peated.
9.6 Deleting transmitters
Deleting an individual transmitter
If there is a transmitter that is faulty or that can no
longer be identified, it is possible that all transmit-
ters must be deleted. System components then
have to be taught-in again. (This is recommended
if a transmitter was lost or is faulty.)
1. In order to delete the required transmitter, the
transmitter teach-in process (RLS RC, radio
switch or window contact) has to be re-
peated→ previous chapter.
Deleting all transmitters
1. Activate teach-in mode on the master fan (re-
ceiver).
ð
The LED flashes, teach-in mode is activ-
ated.
2. Press the teach-in button briefly
twice
.
ð
LED flashes briefly
twice
and then goes
out.
3. Press the teach-in button on the slave fan
(transmitter) for > 1 second until the LED on
the fan lights up briefly
once
.
ð
All taught-in transmitters are deleted. The
fan is again in its initial state.
9.7 Setting up the fan as a signal
amplifier (Repeater)
The radio electronics in the fan can also be used
as a signal amplifier. In this case, the fan that is
set up this way works additionally as a signal
amplifier. EnOcean telegrams are received and
forwarded in parallel to the running application.
This can be necessary for example, with applica-
tions in single-family homes that are completely
automated with EnOcean products.
Settings values
• Off
• Level 1 = Original telegrams are amplified
• Level 2 = Original telegrams and telegrams that
have already been amplified are amplified
Setting up the fan as a signal amplifier
1. Activate teach-in mode on the receiver (fan).
ð
The LED flashes, teach-in mode is activ-
ated.
2. Press the teach-in button briefly
three times
.
ð
The LED lights up briefly and then flashes
briefly three times.
