background image

6 Mounting preparations

16

 DANGER Risk of incorrect installation if

non-permitted mounting material is used.

Only secure connection duct to ceiling with per-
mitted mounting material (duct clamp or clamping
band).

4. Connect permitted connection duct to main

duct and seal for ventilation, for example with
cold-shrink tape.

5. Apply wall/board compound. Seal gap

between brickwork and folded spiral-seams
duct. The gap remaining must be fully sealed
with non-flammable materials that are resist-
ant to deformation. For example, use concrete
or cement mortar or for wall boards, use fire
protection filler.

6. Fit suspended ceiling. Use ER GH housings to

ensure a suitable, flat surface so that the fan
insert can be safely inserted in the housing
later on.

7. Lay power cable: 

Electrically connecting the

unit [

}

 23]

.

6.4 Preparations for the electrical
connection

• Always note the relevant specifications for elec-

trical installations and when fitting equipment. In
Germany, observe DIN VDE 0100 and the cor-
responding parts in particular.

• Observe ambient conditions (

Environmental

conditions and operating limits [

}

 10]

) and

technical data (

Technical data [

}

 10]

).

• Observe permitted duct cross-section of max.

1.5 mm².

1. Lay power cable to the installation location.

2. Continue with the safety test of the release

device: 

Preparing the shutter [

}

 16]

.

6.5 Preparing the shutter

NOTICE Odours may escape from the ventila-
tion channel.

If the installation position is wrong, the plastic
shutter will not close leak-tight.
Insert shutter at the top/to the right/to the left/to
rear in the exhaust socket of the housing to fit the
installation position. Ensure that the shutter
closes entirely leak-tight.

 Before fitting housing, it is essential that

the position of the shutter is checked and its
function ensured.

 For wall installation with air outlet direction

(exhaust socket) to the 

left

 or 

right

, install the

shutter rotated by 90°, see following figures.

Prepare plastic shutter: Air outlet to top, left
or right

Wall installation

1.

Upwards air outlet direction:

 Do not carry

out any modifications (factory setting).

2.

Air outlet direction to the left or right:

 Pull

the shutter out of the exhaust socket, depend-
ing on the installation position, rotate and rein-
sert it. Make sure that the shutter is pushed up
to stop in the exhaust socket.

As a rule, use the standard installation position
with upwards air outlet direction 

for ceiling in-

stallation

 (factory setting).

Summary of Contents for ER shell

































Reviews: