background image

13

Majestic  •  MDVI30IN, MDVI35IN Owner’s Manual  •  2205-981 Rev. D  •  8/16    

Decorative Front

Frequency: 

Annually

By:  

Homeowner

Tools needed

:  Protective gloves, stable work surface

•  Assess condition of screen and replace as necessary.  
•  Inspect for scratches, dents or other damage and repair 

as necessary.

 

Vacuum and dust surfaces.

Figure 4.1  Fixed Glass Assembly

Replacing Fixed Glass Assembly

•  

Tilt glass assembly toward 

fi

 replace and slide glass 

assembly upward to engage top latches. Verify top 
latches are fully engaged and then fasten the two 
bottom latches.

•  Reinstall door or decorative front.

Remote Control

Frequency: 

Seasonally

By:  

Homeowner

Tools needed: 

 Replacement batteries and remote con-

trol instructions.
•  Locate remote control transmitter and receiver.
•  Verify operation of remote. Refer to remote control 

operation instructions for proper calibration and setup 
procedure.

•  Place batteries as needed in remote transmitters and 

battery-powered receivers.

•  Place remote control out of reach of children.
If not using your 

fi

 replace for an extended period of time 

(summer months, vacations/trips, etc), to prevent unin-
tended operation:
•  Remove batteries from remote controls.
•  Unplug 6 volt adapter plug on IPI models.

Venting

Frequency: 

Seasonally

By:  

Homeowner

Tools needed: 

 Protective gloves and safety glasses.

•  Inspect venting and termination cap for blockage or 

obstruction such plants, bird nests, leaves, snow, debris, 
etc.

•  Verify termination cap clearance to subsequent construc-

tion (building additions, decks, fences, or sheds).  

•  Inspect for corrosion or separation.
•  Verify weather stripping, sealing and 

fl

 ashing  remains 

intact.

•  Inspect draft shield to verify it is not damaged or missing.

Summary of Contents for MDVI30IN
























Reviews: