background image

53D0419

Designer Series Gas Fireplaces

3

4.  Never install the fireplace 

• 

in a recreational vehicle

• 

where curtains, furniture, clothing, or other flammable 

objects are less than 4" from the front, top, or sides 

of the fireplace

  in high traffic areas

  in windy or drafty areas 

5.  This fireplace reaches high temperatures. Keep children 

and adults away from hot surfaces to avoid burns or 

clothing ignition. Fireplace will remain hot for a time after 

shutdown. Allow surfaces to cool before touching. 

6.  Carefully supervise young children when they are in 

the room with fireplace. 

7.  Do not modify fireplace under any circumstances. Any 

parts removed for servicing must be replaced prior to 

operating fireplace. 

8.  Turn fireplace off and let cool before servicing, install-

ing, or repairing. Only a qualified service person should 

install,  service,  or  repair  the  fireplace.  Have  burner 

system  inspected  annually  by  a  qualified  service 

person. 

9.  You  must  keep  control  compartments,  burners,  and 

circulating air passages clean. More frequent cleaning 

may be needed due to excessive lint and dust from 

carpeting, bedding material, pet hair, etc. Turn off the 

gas valve and pilot light before cleaning fireplace. 

10. Have venting system inspected annually by a qualified 

service person. If needed, have venting system cleaned 

or repaired. Refer to 

Cleaning and Maintenance

, Page 

39. 

11.  Keep the area around your fireplace clear of combus-

tible materials, gasoline, and other flammable vapor and 

liquids. Do not run fireplace where these are used or 

stored. Do not place items such as clothing or decora-

tions on or around fireplace. 

1.  Do not use this fireplace to cook food or burn paper or 

other objects.

13. Never place anything on top of fireplace.

INSTaLLER

Please leave these instructions with the owner.

owNER

Please retain these instructions for future reference.

IMPoRTaNT SaFETy INFoRMaTIoN

This fireplace is a vented product. This fireplace must be 

properly installed by a qualified service person. The glass 

door must be properly seated and sealed. If this unit is not 

properly installed by a qualified service person with glass 

door properly seated and sealed, combustion leakage can 

occur. 

CaRBoN MoNoxIDE PoISoNING:

 Early signs of carbon 

monoxide poisoning are similar to the flu with headaches, 

dizziness and/or nausea. If you have these signs, the fire-

place may not have been installed properly. Get fresh air 

at once! Have the fireplace inspected and serviced by a 

qualified service person. Some people are more affected 

by carbon monoxide than others. These include pregnant 

women,  people  with  heart  or  lung  disease  or  anemia, 

those  under  the  influence  of  alcohol,  and  those  at  high 

altitudes. 
Propane/LP  gas  and  natural  gas  are  both  odorless. An 

odor-making agent is added to each of these gases. The 

odor helps you detect a gas leak. However, the odor added 

to these gases can fade. Gas may be present even though 

no odor exists.
Make certain you read and understand all warnings. Keep 

this manual for reference. It is your guide to safe and proper 

operation of this fireplace.
1.  This  appliance  is  only  for  use  with  the  type  of  gas 

indicated  on  the  rating  plate. This  appliance  is  not 

convertible for use with other gases unless a certified 

kit is used. 

.  For  propane/LP  fireplace,  do  not  place  propane/LP 

supply tank(s) inside any structure. Locate propane/

LP supply tank(s) outdoors. To prevent performance 

problems, do not use propane/LP fuel tank of less than 

100 gal. capacity. 

3.  If you smell gas

• 

shut off gas supply.

• 

do not try to light any appliance.

• 

do not touch any electrical switch; do not use any 

phone in your building .

• 

immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

• 

Read this owner’s manual carefully and completely before trying to assemble, operate, 

or service this fireplace. 

• 

any change to this fireplace or its controls can be dangerous.

• 

Improper installation or use of this fireplace can cause serious injury or death from 

fire, burns, explosions, electrical shock and carbon monoxide poisoning.

w

a

RNING

Summary of Contents for DVDNV

















































Reviews: