P.2
INSTALLATION
Plug the AC/DC adaptor to an AC household outlet, and then plug the DC jack to the back of the unit. Your clock radio is
ready to work for you.
BACKUP BATTERY INSTALLATION
1. Place your unit face down on a flat surface.
2. Slide and remove the battery cover at the bottom of your unit.
3. Insert one CR2032 lithium battery into the battery compartment with the “+” side facing up as indicated.
4. Replace the battery cover.
If AC power is interrupted, the LED display will go off and both the radio and the alarm will not function. The backup battery
will keep the time and all settings of your unit. Make sure a fresh CR2032 lithium battery is used. A fresh CR2032 battery
could backup your clock continuously for around 3 days.
SETTING TIME, 12/24HR TIME AND THE SNOOZE DURATION
1. Press
SET
once, the hour digits flash. Press or to set the current hour (hold to advance rapidly).
2. Press
SET
again, the minute digits flash. Press or to set minutes.
3. Press
SET
again, the display shows “
24Hr
” and flashes, Press or to select “
12Hr
” or “
24Hr
” time format.
4. Press
SET
again, the display shows “
05
” and flashes, Press or to select your snooze time from 5 to 60 minutes.
If no button will be pressed within 10 seconds, the unit will will exit the setting mode.
Note: when 12-hour time format is selected, the
P
(PM) icon will appear on the lower middle time display to indicate the
afternoon time; there is no AM indicator.
SETTING THE ALARMS
1. Press
AL 1.2
once, the
A1
icon and the hour digits flash. Press or to set the alarm 1 hour.
2. Press
AL 1.2
again to adjust minutes. Press or to set the alarm 1 minutes.
3. Press
AL 1.2
again, LED displays “
OFF
” (alarm off). To select wake to sound sources, press or to select :-
rd
= wake-by-radio
bu
= wake-by-buzzer
OFF
= alarm off
4. Press
AL 1.2
again, the
A2
icon and the hour digits flash. Press or to set the alarm 2 hour. Repeat step 2) and 3)
to set alarm 2.
5. Press
AL1.2
again or no button around 10 seconds to exit alarm setting mode. When wake-to-radio or wake-to-
buzzer is selected, the related alarm is turned on, indicated by appearance of the
A1
and / or the
A2
icon on the left
side of the display.
STOPPING AND RESETTING THE ALARM TO COME ON THE NEXT DAY
When alarm 1 or 2 is sounding, the related
A1 or A2
icon flashes. Press the
AL 1.2
once to stop the alarm and reset it to
come on the following day.
Note: When alarm is sounding, press the /
NAP
or
RADIO / SLEEP
will activate the nap timer or the radio and stop the
alarm for the day.
SNOOZE OPERATION (default snooze duration is 5 minutes)
When alarm is sounding, presses
once, the alarm will be silenced and come on again after the set snooze duration.
Note: if your second alarm activates while the first alarm is sounding or it is in the snooze mode, the second alarm
overrides the first alarm (the first alarm is reset to come on the next day).
USING THE HI-LO DIMMER
Press
to adjust the brightness of the LED display.
USING THE NAP TIMER
1. Press /
NAP
once, the display shows the nap icon and the default naptime “
05
” (5 minutes).
2. Press /
NAP
again to select your desired naptime (5-15-30-45-60-75-90 minutes). It will exit to time display if no
button pressed for 5 seconds.
3. The nap icon lights up when the nap timer is counting. When the nap timer reaches 0, the alarm will sound and the nap
icon will flash. Press
/ NAP
once to stop the nap alarm , the nap icon will go off.
Note: if the nap time is set up then your alarm is sounding, your nap time will be cancelled automatically.
SETTING UP THE FM ANTENNA
Extend the FM wire antenna fully and vary the direction for best FM reception. Do not strip, alter or attach to other
antennas.
Summary of Contents for RSW 401
Page 1: ......
Page 2: ...P 2...
Page 8: ...P 1 INSTRUCTION MANUAL OF RSW 401 LED WEATHER FORCAST RADIO ALARM CLOCK...