background image

Introduction to product

mBot interactive light & sound pack is a 3-in-1 add-on pack. With the parts in the pack, 

you can build out three robots based on mBot : “light chasing robot”, “intelligent desk 

light” and “scorpion robot”. 

Light chasing robot:

It detects the light intensity around mBot via 

two light sensors on each side. When the light 

intensity on the left side is greater than that on 

the right side, the robot will turn left; when the 

light intensity on the right side is greater than 

that on the left side, the robot will turn right; 

otherwise, the robot will go straight.

Intelligent desk light:

By changing the building configuration, mBot 

can turn into an “intelligent desk light”. The 

light has two operating modes: touch mode in 

which the light brightness can be regulated by 

touching the line follower sensor with fingers, 

and voice control mode, in which the sound 

intensity in the surrounding area has to be 

sensed, and when the intensity is large, the light 

will come on, like the voice-activated light at the 

stairway in our daily life.

Scorpion robot:
Add mBot with a vivid “tail”, enabling it to look 
like a scorpion. In this case, by adding an arc tail 
at the rear part of mBot, the center of gravity of 
the robot is changed, thus making it easier for 
the mBot to raise its head. 

Mak

eblock

Makeblock

Makeblock

2

Summary of Contents for mBot



























Reviews: