4V2A1563 (E)
6 - 41
9. Remove O-ring [3] (
10. Determine initial switch
setting (
A. Measure from the sensor
face to the back face of the
switch bracket, dimension
A.
B. Measure from the sensor
face to the end of switch
holder, dimension B.
Dimension B should not
exceed 6mm (0.236").
11. Loosen the two (M4x12) set
screws [10] and pull sensor
[1] out of holder [9].
12. Remove O-ring [2] from inside
the switch holder. Inspect the
O-ring and replace, if there
are any signs of damage. Use
a good quality O-ring lubricant
when replacing the O-ring.
13. Install the new switch sensor [1] into its holder [9]. Be careful not to
pinch or cut the O-ring [2].
14. Set the sensor face to the distances measured in
S
TEP
9
15. Place the switch bracket assembly and O-ring [3] into the spindle
casting and install the two mounting screws.
16. Mount the switch amplifier on its mounting bracket.
17. Connect the fishing line to the new switch wires and pull the wiring
back to the spindle head terminal box.
18. Connect the switch wires at TB2 and replace the terminal box cover.
19. Power up the machine and adjust the prox switch(es), as described in
20. Replace spindle covers and associated parts removed in
S
TEP
1
.
F
IGURE
6-27
SWITCH
BRACKET
ASSEMBLY
F
IGURE
6-28
INITIAL
SWITCH
SET
-
More Detail
1. First set dimension B, then set dimension A.
2. It may be necessary to loosen set screw [4] and turn adjusting nut [5] to obtain
dimension A. If so, tighten set screw [4] after setting A.
Summary of Contents for V55
