7 - 32
7.7.3
LM Guide Installation
All axes have two guide rails. The X and Y axes have two guide blocks per
rail and the Z axis has three guide blocks per rail. The mounting character-
istic for each axis is defined below.
•
The X axis rails are stationary mounted to the top of the column and
the blocks are mounted to the saddle.
•
The Y axis rails are mounted to the bed and the blocks are mounted to
the table.
•
The Z axis rails are mounted to the front of the saddle and the blocks
are mounted to the ram.
Each axis contains a “datum” and a “subsidiary”. The datum rail is aligned
to ball screw centerline and the subsidiary rail aligned to the datum rail.
7.7.4
LM Guide Replacement
Makino uses “Precision Grade” guides which permits individual guide
replacement (rather than sets). Also, the guides contain end, side, and
inner seals to prevent contamination of the re-circulating balls.
Damage to the guide rails and blocks may occur in the event of a machine
wreck. Makino recommends replacing the guide rail and block assembly if
either component is damaged. Rail damage may not be apparent to the
naked eye.
Guide Rail Replacement
Guide rail installation and replacement should be performed only be qualified person-
nel, since the installation process sets the proper preload for the guide rail blocks.
Summary of Contents for V55
