7 - 56
7.9.1.3
Roll-up Cover Assembly and Installation
Cover Assembly:
1. Attach the new cover to the roller.
-
Use extreme CAUTION when performing Step 2, since this step
spring loads the roll-up mechanism.
2. Roll up the new cover by the same number turns used to unroll the old
cover off the roller.
3. Tighten the locking screw [2].
4. Measure the amount of cover extending beyond the roller.
-
It should extend approximately the same distance measured in
Step 2 in the preceding procedure “To Disassemble the Cover”.
5. Attach the bracket [9] to the free end of the cover. Seven (M4x10)
screws [10].
6. Rewrap the tensioner cable [4] around the roller [5] by the same
number of wraps recorded in Step 3 in the preceding procedure “To
Disassemble the Cover”.
Installing the Cover Assembly:
1. Place the cover assembly into position on the machine.
2. Attach the housing [3] to the side frame work [1]. Seven (M5x12)
screws, (M5) flat washers, and (M5) lock washers.
3. Slide the cover [12] through its two guides [7] and [11].
4. Attach the bracket [9] to the saddle cover [8]. Three (M5x8mm)
screws.
-
It may be necessary to temporarily loosen locking screw [2] to
extend the cover for attachment to the saddle cover [8]. If this is
necessary, use extreme CAUTION since the roller mechanism is
now spring loaded.
5. Connect the tensioner cables [4] and adjust tension if necessary, see
6. Install the bracket [14], with the wiper [6] attached. Four (M5x8)
screws.
7. Loosen the locking screw [2].
8. Start the machine.
9. In a Manual mode, at a slow traverse rate, position the X axis back and
forth while observing the roll-up and extension action of both covers.
Summary of Contents for V55
