8 - 42
8.8.1.2
Cylinder Cushion Adjustments
The ATC shutter air cylinder has cushion adjustments, on both ends of the
cylinder, for adjusting the stopping rate at the end of each stroke.
The objective is to set these
adjustments to obtain a slow
down at the end of stroke and
prevent hard stops when the
shutter is opened and closed.
•
The initial cushion
adjustment settings are 1 to
1 ½ turns from closed.
To Adjust Cushioning:
1. Remove the sheet metal
cover to the left of the S/G
door for switch access. Six
(M4x8) cross-head screws.
2. Observe shutter operation
while opening and closing, using Maintenance mode, see
A. Open the shutter; use the cursor keys to select
ATC SHUTER OPEN
and press the [ON] softkey.
B. Close the shutter; use the cursor keys to select
ATC SHUTR CLOSE
and press the [ON] softkey.
3. If shutter stops hard, adjust the appropriate cushion by.
A. Loosen the adjusting screw jam nut [2].
B. Turn the adjusting screw clockwise[3], closing the valve, to obtain
more cushioning or counterclockwise to obtain less cushioning.
C. Tighten the jam nut [2].
4. Open and close the shutter and observe its operation. Repeat Step 3,
if further adjustment is necessary.
5. Install the S/G cover removed in Step 1.
F
IGURE
8-21
CYLINDER
CUSHION
ADJUSTMENTS
Summary of Contents for V55
