7 - 46
7.8.7.2
Establishing Machine Zero Positions
The correct position of machine zero for an axis allows the full axis stroke
to be obtained and aligns the axis with other machine components like the
ATC, APC, etc. Machine zero is set at the factory and does not change
unless the relationship between a ball screw and servo motor changes.
After maintenance functions such as ball screw or servo motor replace-
ment, machine zero for that axis must be reset. Machine wrecks that
result in ball screw-to-motor coupling slippage also requires resetting
machine zero.
The V55 uses absolute position pulse coders in the servo motors. This
means that the machine zero positions are always remembered (stored),
even through a machine power Off and On sequence. Even though
machine zero is stored, the PMC software requires that all machine axes
be aligned by performing a reference operation at machine power On.
When an axis is referenced, it is aligned to pulse coder marker pulse. This
is not the “true” machine zero position. Machine zero is typically a position
that is shifted from the pulse coder marker pulse by a value set into the
Grid Shift parameter 1850. Parameter 1850 provides the ability to shift all
machine axes separately.
This section describes how to determine the machine zero position for
each axis and the setting values for Grid Shift parameter 1850.
Parameter 1850 Setting Values:
Parameter 1850 setting values are entered as “detection units” in the
range of ±99999999. Since the V55 uses metric ball screws, one
detection unit is equal to the least input increment of the metric mode.
-
One detection unit = 0.001mm
Grid Shift Parameter 1850
The true axis reference position may be adjusted in the plus or minus direction from
the grid point by setting Grid Shift parameter 1850. The value set into 1850 tells the
CNC to add or subtract the set value from the pulse coder grid point.
The setting value for parameter 1850 is in detect units and is based on the metric sys-
tem. One detect unit is equal to 0.001 mm. After changing parameter 1850, power
must be turned Off and back On, before the parameter change becomes effective.
Summary of Contents for V55
