2 - 20
2.4.2
Electrical Power
A 3-phase power source, with stable voltage regulation (±10%) and a
ground of 100 ohms or less, must be provided. A step down transformer is
provided to help regulate voltage and allow for different voltages.
The V55 is set up to run on 200/220 VAC, 55 kVa, 50/60 Hz ±2% off the
secondary side of the transformer. Secondary voltage output is connected
to a terminal point in the MTC.
•
Provide a properly sized service box for the machine. Use local code
and
to assist in sizing the machine’s electrical service. Use
the machine kVa rating when calculating machine electrical
consumption.
•
Ensure the electrical service voltages meet all requirements; 200/220
VAC (±10%), 75 kVa, 50/60 Hz, and a proper earth ground (100 ohms
or less) is provided.
•
If the required voltage cannot be maintained within ±10%, an additional
automatic voltage regulator must be installed.
•
Connect incoming electrical service to the machining center Main
Power switch, as described in the Pre-Installation Guide.
T
ABLE
2-10
MACHINE
POWER
REQUIREMENTS
To convert kVa to amperage
for service amperage:
Power Requirements
14,000 rpm
20,000 rpm
Machine
kVa Rating
55 kVa
65 kVa
then take:
amps × 125% = Service
Source
Voltage
200–480V
[±10%]
200–480V
[±10%]
Operating
Voltage
200–220V
[±10%]
200–220V
[±10%]
Cycle
50/60Hz
[±2%]
50/60Hz
[±2%]
kVa
1000
×
1.73
Voltage
×
-------------------------------------
amps
=
Summary of Contents for V55
