12 ENGLISH
Side handle
►
Fig.7:
1.
Side handle
2.
Clamp nut
The side handle can be swung in a vertical direction and
secured at any desired position. It can also be adjusted
at eight steps back and forth in a horizontal direction.
Loosen the clamp nut to swing the side handle to a
desired position, and then tighten the clamp nut securely.
Side grip (auxiliary handle)
The side grip can be swung, allowing easy handling of
the tool in any position. Loosen the side grip by turning
it counterclockwise, swing it to the desired position and
then tighten it by turning clockwise.
►
Fig.8:
1.
Side grip
Installing or removing bit
Grease
Clean the shank end of the bit and apply grease before
installing the bit.
Coat the shank end of the bit beforehand with a small
amount of grease (about 0.5 - 1 g). This chuck lubrica
-
tion assures smooth action and longer service life.
►
Fig.9:
1.
Shank end
2.
Grease
Insert the bit into the tool. Turn the bit and push it in until
it engages. After installing the bit, always make sure
that the bit is securely held in place by trying to pull it
out.
►
Fig.10:
1.
Bit
To remove the bit, pull the chuck cover down all the way
and pull the bit out.
►
Fig.11:
1.
Bit
2.
Chuck cover
Bit angle
The bit can be secured at 12 different angles. To
change the bit angle, slide the change ring forward,
then turn the change ring to change the bit angle. At the
desired angle, slide the change ring back to the original
position. The bit will be secured in place.
After changing the bit angle, make sure the angle is
fixed by trying to rotate the bit.
►
Fig.12:
1.
Change ring
Dust extractor attachment
Optional accessory
1.
Install the hose holder (A/B).
When the side handle is installed to tool, loosen the
clamp nut, and then remove the hex bolt. Install the
hose holder (A) between the hex bolt and the clamp nut
by tightening the clamp nut firmly.
►
Fig.13:
1.
Hex bolt
2.
Hose holder (A)
3.
Clamp nut
When the side grip is installed to the tool, loosen the
side grip, mount the hose holder (B) to the shaft, and
then tighten the side grip firmly.
►
Fig.14:
1.
Hose holder (B)
2.
Shaft
3.
Side grip
2.
Attach the holder joint to the tool, and then attach
the hose holder (C) to the holder joint.
►
Fig.15:
1.
Holder joint
2.
Hose holder (C)
NOTE:
The hose joint can be attached to either side
of the tool.
WARNING:
Use the mounting part of the tool
only for attaching the holder joint.
Using the mounting part for any other purpose may
cause an unexpected accident.
3.
Attach the dust cover and the hose to the tool, and
then fix the hose to the hose holders.
►
Fig.16:
1.
Dust cover
2.
Hose
3.
Hose holder (A/B)
4.
Hose holder (C)
4.
Connect the hose to the hose of the vacuum
cleaner with the hose joint.
NOTE:
If the hose is not included, attach the dust
cover to the cleaner's joint or attach it to Makita's
hose ø28.
5.
Adjust the distance between the dust cover and
the tip of the chisel or bull point. The recommended
distance is 30 mm to 100 mm.
►
Fig.17:
(1)
30 mm to 100 mm
OPERATION
CAUTION:
Always use the side handle / side
grip (auxiliary handle) and firmly hold the tool by
both side handle / side grip and switch handle
during operations.
CAUTION:
Always make sure that the work-
piece is secured before operation.
Failure to prop
-
erly secure the workpiece may cause the workpiece
to move resulting in injury.
CAUTION:
Do not pull the tool out forcibly
even the bit gets stuck. Loss of control may
cause injury.
CAUTION:
Do not leave the tool stabbed in
the workpiece.
Otherwise the tool may starts unin
-
tentionally and cause an injury.
NOTE:
If the battery cartridge is in low temperature,
the tool’s capability may not be fully obtained. In this
case, warm up the battery cartridge by using the
tool with no load for a while to fully obtain the tool’s
capability.
Chipping/Scaling/Demolition
Hold the tool firmly with both hands. Turn the tool on
and apply slight pressure on the tool so that the tool will
not bounce around, uncontrolled. Pressing very hard on
the tool will not increase the efficiency.
►
Fig.18
►
Fig.19
Summary of Contents for 0088381732611
