10 ENGLISH
Opening European type safety
guard
Country specific
For the tools equipped with European type safety guard,
loosen the clamping screw first then open the guard as
shown.
►
Fig.12:
1.
Clamping screw
►
Fig.13
►
Fig.14
Removing or installing cut-off wheel
CAUTION:
Be sure to tighten the toolless
clamp or hex bolt securely.
Insufficient tightening
may result in severe injury. When tightening the hex
bolt, use the socket wrench provided with the tool to
assure proper tightening.
CAUTION:
Always use only the proper inner
and outer flanges which are provided with the
tool.
CAUTION:
Always lower the safety guard
after replacing the wheel.
CAUTION:
Wear gloves when handling
wheels.
►
Fig.15:
1.
Inner flange
2.
Ring
3.
O-ring
4.
Cut-off
wheel
5.
Outer flange
6.
Toolless clamp /
Hex bolt
For LW1400
Raise the safety guard. Turn the toolless clamp coun-
terclockwise while holding down the shaft lock. Then
remove the toolless clamp, outer flange and cut-off
wheel. When removing the cut-off wheel, do not remove
the inner flange as well as the ring and O-ring.
►
Fig.16:
1.
Shaft lock
2.
Toolless clamp
To install the cut-off wheel, follow the removal proce-
dures in reverse. Make sure to fit the hole of cut-off
wheel to the ring and return the safety guard.
For LW1401
Raise the safety guard. Turn the hex bolt counterclock
-
wise using a socket wrench while holding down the
shaft lock. Then remove the hex bolt, outer flange and
wheel.
►
Fig.17:
1.
Shaft lock
2.
Hex bolt
To install the wheel, follow the removal procedures in
reverse. Make sure to fit the hole of cut-off wheel to the
ring and return the safety guard.
OPERATION
CAUTION:
Proper handle pressure during
cutting and maximum cutting efficiency can
be determined by the amount of sparks that is
produced while cutting. Do not force the cut
by applying excessive pressure on the handle.
Reduced cutting efficiency, premature wheel wear, as
well as, possible damage to the tool, cut-off wheel or
workpiece may result.
Hold the handle firmly. Switch on the tool and wait until
the cut-off wheel attains full speed before lowering
gently into the cut. When the cut-off wheel contacts
the workpiece, gradually bear down on the handle to
perform the cut. When the cut is completed, switch off
the tool and
wait until the cut-off wheel has come to
a complete stop
before returning the handle to the fully
elevated position.
Cutting capacity
Maximum cutting capacity varies depending on the
cutting angle and workpiece shape.
Max. cutting capacity with a brand-new cut-off
wheel
Cutting angle /
Workpiece shape
90°
45°
127 mm
127 mm
115 x 130 mm
102 x 194 mm
70 x 233 mm
115 x 103 mm
119 x 119 mm
106 x 106 mm
137 x 137 x 10 mm 100 x 100 x 10 mm
Securing workpiece
CAUTION:
Always place the thread holder on
the shaft threads when securing the workpiece.
Failure to do so may result in insufficient securing of
the workpiece. This could cause the workpiece to be
ejected or cause a dangerous breakage of the cut-off
wheel.
While the thread holder is lifted, the vise plate can be
moved in and out quickly. To grip a workpiece, push the
handle until the vise plate contacts the workpiece then
return the thread holder. Turn the handle clockwise until
the workpiece is securely retained.
►
Fig.18:
1.
Handle
2.
Thread holder
3.
Vise plate
Summary of Contents for 0088381807883
