Makita 9561CH, Instruction Manual

7

b) The grinding surface of centre depressed

wheels must be mounted below the plane of
the guard lip. 

An improperly mounted wheel

that projects through the plane of the guard lip
cannot be adequately protected.

c) The guard must be securely attached to the

power tool and positioned for maximum
safety, so the least amount of wheel is
exposed towards the operator. 

The guard

helps to protect the operator from broken wheel
fragments, accidental contact with wheel and
sparks that could ignite clothing.

d) Wheels must be used only for recommended

applications. For example: do not grind with
the side of cut-off wheel. 

Abrasive cut-off

wheels are intended for peripheral grinding, side
forces applied to these wheels may cause them
to shatter. 

e)  Always use undamaged wheel flanges that

are of correct size and shape for your
selected wheel. 

Proper wheel flanges support

the wheel thus reducing the possibility of wheel
breakage. Flanges for cut-off wheels may be dif-
ferent from grinding wheel flanges. 

f)

Do not use worn down wheels from larger
power tools.

 Wheel intended for larger power

tool is not suitable for the higher speed of a
smaller tool and may burst.

Additional Safety Warnings Specific for Abrasive
Cutting-Off Operations: 

a)

Do not “jam” the cut-off wheel or apply
excessive pressure. Do not attempt to make
an excessive depth of cut. 

Overstressing the

wheel increases the loading and susceptibility to
twisting or binding of the wheel in the cut and the
possibility of kickback or wheel breakage. 

b)

Do not position your body in line with and
behind the rotating wheel. 

When the wheel, at

the point of operation, is moving away from your
body, the possible kickback may propel the spin-
ning wheel and the power tool directly at you. 

c) When wheel is binding or when interrupting a

cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the
cut while the wheel is in motion otherwise
kickback may occur. 

Investigate and take cor-

rective action to eliminate the cause of wheel
binding.

d)

Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. 

The wheel may

bind, walk up or kickback if the power tool is
restarted in the workpiece. 

e)  Support panels or any oversized workpiece

to minimize the risk of wheel pinching and
kickback. 

Large workpieces tend to sag under

their own weight. Supports must be placed under
the workpiece near the line of cut and near the
edge of the workpiece on both sides of the
wheel.

f)

Use extra caution when making a “pocket
cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can cause
kickback.

Safety Warnings Specific for Sanding Operations: 

a)

Do not use excessively oversized sanding
disc paper. Follow manufacturers recommen-
dations, when selecting sanding paper.

Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and
may cause snagging, tearing of the disc or kick-
back. 

Safety Warnings Specific for Wire Brushing Opera-
tions: 

a) Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not
overstress the wires by applying excessive
load to the brush. 

The wire bristles can easily

penetrate light clothing and/or skin. 

b) If the use of a guard is recommended for wire

brushing, do not allow interference of the
wire wheel or brush with the guard. 

Wire

wheel or brush may expand in diameter due to
work load and centrifugal forces.

Additional Safety Warnings:
17. When using depressed center grinding wheels,

be sure to use only fiberglass-reinforced wheels.

18. NEVER USE Stone Cup type wheels with this

grinder. 

This grinder is not designed for these types

of wheels and the use of such a product may result
in serious personal injury.

19. Be careful not to damage the spindle, the flange

(especially the installing surface) or the lock nut.
Damage to these parts could result in wheel
breakage.

20. Make sure the wheel is not contacting the work-

piece before the switch is turned on. 

21. Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced wheel.

22. Use the specified surface of the wheel to per-

form the grinding.

23. Do not leave the tool running. Operate the tool

only when hand-held.

24. Do not touch the workpiece immediately after

operation; it may be extremely hot and could
burn your skin.

25. Observe the instructions of the manufacturer for

correct mounting and use of wheels. Handle and
store wheels with care.

26. Do not use separate reducing bushings or adap-

tors to adapt large hole abrasive wheels. 

27. Use only flanges specified for this tool. 
28. For tools intended to be fitted with threaded hole

wheel, ensure that the thread in the wheel is long
enough to accept the spindle length. 

29. Check that the workpiece is properly supported.
30. Pay attention that the wheel continues to rotate

after the tool is switched off.

31. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a short-
circuit breaker (30 mA) to assure operator safety.

32. Do not use the tool on any materials containing

asbestos.