4
ENGLISH (Original instructions)
Explanation of general view
1-1. Button
1-2. Red indicator
1-3. Battery cartridge
2-1. Star marking
3-1. Die holder
3-2. Lock nut
3-3. Loosen
3-4. Wrench
4-1. Gauge for cutting stainless:
1.2 mm (3/64")
4-2. Gauge for cutting mild steel:
1.6 mm (1/16")
4-3. Notch
5-1. Slide switch
6-1. Indicating lamp
7-1. Die holder
7-2. Die
7-3. Bolts
7-4. Hex wrench
8-1. Punch
8-2. Punch holder
8-3. Screw
8-4. Hex wrench
8-5. Loosen
8-6. Tighten
9-1. Punch
9-2. Notch
10-1. Bolts
10-2. Die
10-3. Punch
10-4. Die holder
13-1. From the side view
13-2. Cutting head should be at a right
angle (90
ﾟ
) to cutting surface.
14-1. Limit mark
15-1. Holder cap cover
15-2. Notch
15-3. Screwdriver
16-1. Brush holder cap
16-2. Screwdriver
SPECIFICATIONS
Model BJN160
BJN161
Steel up to 400 N/mm
2
1.6 mm / 16 ga
1.6 mm / 16 ga
Steel up to 600 N/mm
2
1.2 mm / 18 ga
1.2 mm / 18 ga
Max. cutting capacities
Aluminum up to 200 N/mm
2
2.5 mm / 12 ga
2.5 mm / 12 ga
Outside edge
50 mm
50 mm
Min. cutting radius
Inside edge
45 mm
45 mm
Strokes per minute (min
-1
) 1,900
1,900
Overall length
313 mm
313 mm
Net weight
2.1 kg
2.2 kg
Rated voltage
D.C. 14.4 V
D.C. 18 V
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
ENE037-1
Intended use
The tool is intended for cutting sheet steel and stainless
sheet steel.
ENG905-1
Noise
The typical A-weighted noise level determined
according to EN60745:
Model BJN160
Sound pressure level (L
pA
) : 72 dB (A)
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model BJN161
Sound pressure level (L
pA
) : 73 dB (A)
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
ENG900-1
Vibration
The vibration total value (tri-axial vector sum)
determined according to EN60745:
Model BJN160
Work mode : cutting sheet metal
Vibration emission (a
h
) : 7.0 m/s
2
Uncertainty (K) : 1.5 m/s
2
Model BJN161
Work mode : cutting sheet metal
Vibration emission (a
h
) : 6.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
ENG901-1
•
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
•
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
