Makita CF100D, Owner'S Manual

7

HOW TO OPERATE THE UNIT

 WARNING

•  Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient 

to inflict serious injury.

•  Do not use any batteries, attachments or accessories not recommended by the manufacturer of this tool. The use 

of batteries, attachments or accessories not recommended can result in serious personal injury.

•  Do not handle the cord and battery with wet or greasy hand.

•  Never use the cordless fan when the cord or plug is damaged.

•  Do not leave the AC adapter disconnected from the cordless fan while the power is supplied from the mains. Small 

children may put the live plug in their mouth and cause injury.

•  When inserting/removing the battery or plugging/unplugging the AC adapter, always place the cordless fan on a flat 

and stable surface.

This fan is equipped with a 3-speed control using the speed switch. Power supply can be with AC adaptor or 

battery cartridge (OPTIONAL ACCESSORIES).

USING AC ADAPTOR

Insert the 12V DC plug of AC adaptor into the 12V DC socket 

(Fig. 2)

, and then plug the AC pins into a main power 

supply. Make sure that the voltage rating of the main power supply corresponds with that of the adaptor.

SAVE THESE INSTRUCTIONS

After the AC adaptor is connected, the cordless fan may take 3–5 seconds to start. 
The adaptor might creak while using it for the power supply. This doesn’t affect normal use.
The supplied AC adapter does not charge the battery inserted to the cordless fan.

USING BATTERY CARTRIDGE

IN ORDER TO ENSURE THE BATTERY MAXIMUM PERFORMACE, IT IS RECOMMENDED THAT THE BATTERY 

CARTRIDGE SHOULD BE CHARGED BEFORE BEING USED FOR THE FIRST TIME.

1.  Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, 

and (3) product using battery.

2.  Do not disassemble battery cartridge.

3.  If operating time has become excessively shorter, stop operating immediately. It may result in a risk of 

overheating, possible burns or even an explosion.

4.  If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may 

result in loss of your eyesight.

5.  Do not shorten the battery cartridge:

(1) Do not touch the terminals with any conductive material.

(2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.

(3) Do not expose battery cartridge to water or rain.

A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

6.  Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).

7.  Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery 

cartridge can explode in a fire.

8.  Be careful not to drop or strike battery.

9.  Do not use a damaged battery.

10. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.

11. The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. For commercial 

transports e.g. by third parties, forwarding agents, special requirement on packaging and labeling must be 

observed. For preparation of the item being shipped, consulting an expert for hazardous material is required. 

Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the 

battery in such a manner that it cannot move around in the packaging.

12. Follow your local regulations relating to disposal of battery.

SAVE THESE INSTRUCTIONS

 CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing 

fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.

Tips for maintaining maximum battery life:

1.  Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery 

cartridge when you notice less tool power. 

2.  Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.