13 ENGLISH
Installing or removing stay / HEPA filter
Optional accessory
For the stay and sponge filter
To remove the stay, push up the bottom part of pillars
of the stay with your fingers and release its groove from
the protrusion on the cleaner. After that, remove the
sponge filter.
►
Fig.17:
1.
Stay
2.
Sponge filter
To install, align the grooves on the stay with the protru-
sion on the cleaner and push until it clicks.
Insert the sponge filter between the pillars and set it in
the original position.
For the HEPA filter
When installing the HEPA filter, fit the groove of the
HEPA filter with the protrusion on the cleaner. Then, put
the prefilter or the high performance filter on the HEPA
filter and twist it to secure. To remove, follow the instal
-
lation procedure in reverse.
►
Fig.18:
1.
HEPA filter
2.
Prefilter
►
Fig.19:
1.
HEPA filter
2.
High performance filter
OPERATION
CAUTION:
Do not move your face close to
the air vent when operating the cleaner.
If foreign
objects are blown into eyes, it may result in personal
injury.
Installing or removing the cleaner
attachment
CAUTION:
After installing attachment,
check if it is securely installed.
If the attachment
is installed imperfectly, it may come off and cause
personal injury.
CAUTION:
Be careful not to hit your hand on
the wall etc. when removing the attachment.
When using attachment with lock
function
To install attachment, insert it to the suction inlet of the
cleaner until it clicks. Make sure that the attachment is
locked.
►
Fig.20:
1.
Suction inlet
2.
Attachment with lock
function
3.
Hook
NOTE:
When installing the attachment with lock
function, be sure to align the release button with
the hook on the attachment.
If they are not aligned,
the wand will not be locked and may come off from
the cleaner.
To remove, pull the attachment while pushing the
release button.
►
Fig.21:
1.
Release button
2.
Attachment with lock
function
When using attachment without lock
function
CAUTION:
To connect attachment without
lock function, twist and insert it in direction of
the arrow to secure the connection during use.
To disconnect the attachment, twist and extract
it also in direction of the arrow.
If the attachment
is twisted in the opposite direction, the capsule may
become loose.
►
Fig.22
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture,
etc. The nozzle slips on easily.
►
Fig.23:
1.
Nozzle
Extension wand (Straight
pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a floor in a standing position.
►
Fig.24:
1.
Cleaner body
2.
Extension wand
3.
Nozzle
Corner nozzle
Fit on the corner nozzle for cleaning corners and crev-
ices of a car or furniture.
►
Fig.25:
1.
Corner nozzle
2.
Cleaner body
You can store the corner nozzle in the nozzle holder.
►
Fig.26:
1.
Nozzle holder
2.
Corner nozzle
CAUTION:
Be careful not to trap finger(s)
between the corner nozzle and the nozzle holder.
Trapping finger(s) may cause injury.
Corner Extension wand
(Straight pipe)
In tight quarters where the cleaner itself cannot
squeeze in, or in high places hard to reach, use this
arrangement.
►
Fig.27:
1.
Corner nozzle
2.
Extension wand
3.
Cleaner body
Cleaning without nozzle
You can pick up powder and dust without nozzle.
►
Fig.28
For picking up dust on a floor in a standing position, it is
convenient to attach the extension wand to the cleaner.
►
Fig.29:
1.
Extension wand
Summary of Contents for CL001G
Page 4: ...2 1 Fig 17 1 2 Fig 18 1 2 Fig 19 3 2 1 Fig 20 1 2 Fig 21 Fig 22 1 Fig 23 4 ...
Page 5: ...3 2 1 Fig 24 2 1 Fig 25 1 2 Fig 26 2 3 1 Fig 27 Fig 28 1 Fig 29 Fig 30 Fig 31 5 ...
Page 6: ...Fig 32 Fig 33 2 1 Fig 34 1 Fig 35 3 4 1 2 5 Fig 36 2 3 1 4 Fig 37 6 ...
Page 7: ...2 1 Fig 38 2 1 Fig 39 1 2 Fig 40 1 2 3 Fig 41 7 ...
