9 ENGLISH
FUNCTIONAL
DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and
the battery cartridge is removed before adjust
-
ing or checking function on the tool.
Installing or removing battery
cartridge
For Model CL072D
►
Fig.1:
1.
Battery cartridge
2.
Button
For Model CL102D
►
Fig.2:
1.
Battery cartridge
2.
Button
•
Always switch off the tool before insertion or
removal of the battery cartridge.
•
To remove the battery cartridge, withdraw it from
the tool while pressing the buttons on both sides
of the cartridge.
•
To insert the battery cartridge, hold it so that the
battery cartridge front shape fits to that of the
battery installment opening and slip it into place.
Always insert it all the way until it locks in place
with a little click. If not, it may accidentally fall
out of the tool, causing injury to you or someone
around you.
•
Do not use force when inserting the battery car-
tridge. If the cartridge does not slide in easily, it is
not being inserted correctly.
Battery protection system
The cleaner is equipped with the protection system,
which automatically cuts off the output power for its long
service life.
The cleaner stops during operation when the cleaner
and/or battery are placed under the following situation.
This is caused by the activation of protection system
and does not show the cleaner trouble.
•
When the cleaner is overloaded:
At this time, release the switch trigger and
remove causes of overload and then pull the
switch trigger again to restart.
•
When the remaining battery capacity gets low:
Recharge the battery cartridge.
Switch action
►
Fig.3:
1.
HIGH/LOW button
2.
OFF button
To start the cleaner, simply press the "HIGH/LOW"
button. To switch off, press the "OFF" button. To change
the cleaner speed, press the "HIGH/LOW" button. The
first press on this button is for high speed and the sec
-
ond press for low speed and then each press on this
button repeats the high/low speed cycle alternatively.
Battery power lamp
►
Fig.4:
1.
Battery power lamp
•
When the remaining battery capacity gets low, the
battery power lamp blinks.
•
When the remaining battery capacity gets much
lower, the tool stops during operation and the bat-
tery power lamp lights up for about ten seconds.
At this time, remove the battery cartridge from the
tool and charge it .
NOTE:
•
The time at which the battery power lamp start
blinking or lighting up depends on the tempera-
ture at work place and the battery cartridge
conditions.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and
the battery cartridge is removed before carrying
out any work on the tool.
Disposing of Dust
CAUTION:
•
Empty the cleaner before it becomes too full, or
the suction force weakens.
•
Be sure to empty out the dust inside the cleaner
itself. Failure to do so may cause the sponge
filter to be clogged or the motor to be damaged.
•
Never throw away the dust stopper because it
should be used whenever either the dust bag or
the paper pack is used.
►
Fig.5:
1.
Front cover
2.
Button
1.
Push the button to open the front cover. Opening
it until a click is heard allows a positive stop at that
position.
►
Fig.6:
1.
Front cover
2.
Front cover joint
NOTE:
•
The cleaner is constructed in such a way that
the front cover comes off when trying to force
the front cover open at the angle of more than
90°. If the front cover comes off, insert it into the
front cover joint in place.
CAUTION:
•
When closing the front cover, be careful not to
pinch your fingers.
►
Fig.7:
1.
Dust stopper
2.
Pull out both the orange-colored dust stopper and
dust bag together at the same time.
►
Fig.8:
1.
Dust stopper
►
Fig.9
3.
Remove the dust stopper and empty the cleaner.
Summary of Contents for CL072D
Page 2: ...1 2 1 2 1 2 1 1 2 1 2 1 1 Fig 1 Fig 2 Fig 3 Fig 4 Fig 5 Fig 6 Fig 7 Fig 8 2 ...
Page 3: ...1 2 1 2 3 1 1 1 Fig 9 Fig 10 Fig 11 Fig 12 Fig 13 Fig 14 Fig 15 Fig 16 3 ...
Page 4: ...1 2 1 2 3 1 1 Fig 17 Fig 18 Fig 19 Fig 20 Fig 21 Fig 22 Fig 23 Fig 24 4 ...
Page 5: ...1 1 2 3 1 2 1 2 3 Fig 29 Fig 25 Fig 26 Fig 27 Fig 28 Fig 30 Fig 31 Fig 32 5 ...
