12 ENGLISH
Problem Examples
Example 1: Only the prefilter has been loaded (no filter)
►
Fig.22:
1.
Prefilter
Example 2: Only the filter has been loaded (no prefilter)
►
Fig.23:
1.
Filter
Example 3: The filter has been loaded in a peeled back
state
►
Fig.24:
1.
Filter
Example 4: The securing lip on the prefilter is not firmly
locked in the groove of cleaner housing
►
Fig.25:
1.
Securing lip
2.
Prefilter
3.
Groove of
cleaner housing
Reassembly for high performance
filter
Connect high performance filter. At this time, make sure
to twist high performance filter so that securing lip is
firmly locked into cleaner unit.
►
Fig.26:
1.
High performance filter
2.
Securing lip
►
Fig.27:
1.
Securing lip
Install the capsule. Align the mark on the capsule with
the mark near the handle and then firmly twist the cap
-
sule in direction of the arrow until it is secured.
►
Fig.28:
1.
Mark
►
Fig.29:
1.
Capsule
2.
Handle
3.
Mark
NOTE:
Always remove dust ahead of time, as suction
power will be reduced if there is too much dust in
cleaner.
NOTE:
Always be sure to check that high perfor-
mance filter is loaded correctly prior to using cleaner.
If they are not loaded correctly, dust will get into the
motor housing, and cause motor failure.
If the following examples occur, high performance
filter is not loaded correctly. Reload them correctly to
rectify problem.
Problem Examples
Securing lip of high performance filter is not firmly
locked into groove of cleaner housing.
►
Fig.30:
1.
Securing lip
2.
Groove of cleaner housing
OPERATION
CAUTION:
To connect attachments, such
as nozzle, twist and insert the attachment in
direction of the arrow to secure the connection
during use. To disconnect the attachments, twist
and extract it also in direction of the arrow.
If an
attachment is twisted in the opposite direction when
being connected or disconnected, the capsule may
become loose.
►
Fig.31:
1.
Capsule
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture,
etc. The nozzle slips on easily.
►
Fig.32:
1.
Nozzle
Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a floor in a standing position.
►
Fig.33:
1.
Cleaner body
2.
Extension wand
3.
Nozzle
Corner nozzle
Fit on the corner nozzle for cleaning corners and crev-
ices of a car or furniture.
►
Fig.34:
1.
Corner nozzle
2.
Cleaner body
Corner Extension wand
(Straight pipe)
In tight quarters where the cleaner itself cannot
squeeze in, or in high places hard to reach, use this
arrangement.
►
Fig.35:
1.
Corner nozzle
2.
Extension wand
3.
Cleaner body
Cleaning without nozzle
You can pick up powder and dust without nozzle.
►
Fig.36
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
After use
NOTICE:
Putting the cleaner against the wall
without any other support cause the cleaner to
fall down and be damaged.
►
Fig.37
Summary of Contents for CL108FDSA
