3
ENGLISH
Explanation of general view
1
Set plate
2
Battery cartridge
3
Button
4
Sleeve
5
Ring
6
Reversing switch lever
7
Switch trigger
8
B side
9
A side
10
Restart button
11
Screw
SPECIFICATIONS
Model
DA302D DA392D DA312D
Capacities
Steel ........................................................... 10 mm
10 mm
10 mm
Wood .......................................................... 10 mm
12 mm
12 mm
Wood screw ................................................ 4.5 mm x 20 mm
4.5 mm x 20 mm
4.5 mm x 20 mm
No load speed (min
-1
) .................................... 0 – 800
0 – 800
0 – 800
Overall length ................................................ 296 mm
324 mm
324 mm
Net weight ...................................................... 1.1 kg
1.3 kg
1.4 kg
Rated voltage ................................................ D.C. 7.2 V
D.C. 9.6 V
D.C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for drilling in wood, metal and plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
ENC004-1
1.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
7.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
8.
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
9.
Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
2.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
4.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
ADDITIONAL SAFETY RULES
ENB022-1
1.
Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
2.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a “live”
wire will also make exposed metal parts of the
tool “live” and shock the operator.
3.
Always be sure you have a firm footing.
4.
Be sure no one is below when using the tool in
high locations.
5.
Hold the tool firmly.
6.
Keep hands away from rotating parts.
7.
Do not leave the tool running. Operate the tool
only when hand-held.
8.
Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
Summary of Contents for DA392D
Page 2: ...2 1 2 3 4 5 6 7 1 2 2 3 7 6 8 9 4 5 10 11 1 ...
Page 43: ...43 ...
Page 44: ...Makita Corporation 884374C992 ...
