background image

CAUTION: 

• 

Before installing the battery cartridge into the tool, 
always check to see that the switch trigger 
actuates properly and returns to the "OFF" 
position when released. 

• 

Do not pull the switch trigger hard without pressing 
the lock-off lever. This can cause switch breakage. 

1

2

 

 

015631 

To prevent the switch trigger from being accidentally 
pulled, a lock-off lever is provided. To start the tool, 
press the lock-off lever and pull the switch trigger. 
Release the switch trigger to stop. 

Indicating remaining battery capacity 

(Country specific) 

1

 

 

015642 

When you turn the tool on, the battery indicator shows 
the remaining battery capacity. 
The remaining battery capacity is shown as the 
following table. 

Battery indicator status

Remaining battery capacity

50% - 100%

20% - 50%

0% - 20%

Charge the battery

On

Off

Blinking

 

015624 

 

Automatic speed change function 

1

 

 

015638 

Mode indicator status

Operation mode

High speed mode

High torque mode

   

015137 

This tool has "high speed mode" and "high torque 
mode". It automatically changes operation mode 
depending on the work load. When mode indicator lights 
up during operation, the tool is in high torque mode. 

Tool / battery protection system 

The tool is equipped with a tool/battery protection 
system. This system automatically cuts off power to the 
motor to extend tool and battery life. 
The tool will automatically stop during operation if the 
tool or battery are placed under one of the following 
conditions. In some conditions, the indicator lights up. 

Overload protection 

When the tool is operated in a manner that causes it to 
draw an abnormally high current, the tool automatically 
stops without any indications. In this situation, turn the 
tool off and stop the application that caused the tool to 
become overloaded. Then turn the tool on to restart. 

Overheat protection for tool 

When the tool is overheated, the tool stops 
automatically and the battery indicator shows following 
state. In this situation, let the tool cool before turning the 
tool on again. 

Battery indicator

Tool is overheated

On

Off

Blinking

   

015625 

 
 
 
 

1. Mode indicator 

1. Battery indicator

1. Switch trigger 
2. Lock-off lever 

Summary of Contents for DCS551RMJ













Reviews: