15 ENGLISH
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
W
Fig.9:
1.
Indicator lamps
2.
Check button
y & -
Indicator lamps
Remaining
capacity
Lighted
Off
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
malfunctioned.
NOTE:
Depending on the conditions of use and the
Switch action
WARNING:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
WARNING:
NEVER defeat the lock-off button
by taping down or some other means.
A switch with
&)
WARNING:
NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-off button.
A switch in need of repair
} z&
for proper repairs BEFORE further usage.
&)
off button is provided. To start the tool, depress the lock-off button
and pull the switch trigger. Release the switch trigger to stop.
W
Fig.10:
1.
Switch trigger
2.
Lock-off button
NOTICE:
Do not pull the switch trigger hard
without pressing in the lock-off button.
This can
cause switch breakage.
CAUTION:
The tool starts to brake the cir-
cular saw blade rotation immediately after you
#'!'$'?'>*?#=='#_!%?'!+#<!^
respond the reaction of the brake when releasing
the switch trigger.
Sudden reaction can drop the tool
Automatic speed change function
This tool has "high speed mode" and "high torque
mode".
&' &
the tool will run in the "high speed mode" for quicker
' &
will run in the "high torque mode" for powerful cutting
operation.
W
Fig.11:
1.
Mode indicator
The mode indicator lights up in green when the tool is
running in "high torque mode".
If the tool is operated with excessive load, the mode
indicator will blink in green. The mode indicator stops
&
load on the tool.
Mode indicator status
Operation
mode
On
Off
Blinking
High speed
mode
High torque
mode
Overload
alert
Adjusting depth of cut
CAUTION:
After adjusting the depth of cut,
always tighten the lever securely.
Loosen the lever on the depth guide and move the base
up or down. At the desired depth of cut, secure the base
For cleaner, safer cuts, set cut depth so that no more
&$
proper cut depth helps to reduce potential for danger-
?[K?#(K?
W
Fig.12:
1.
Lever
Bevel cutting
CAUTION:
After adjusting the bevel angle,
always tighten the clamping screws securely.
Loosen the clamping screws. Set for the desired angle
W
Fig.13:
1.
Clamping screw
$ >I
` =)
45° bevel cut or 0° - 48° bevel cut.
W
Fig.14:
1.
Stopper
Summary of Contents for DHS782ZJ
