16 ENGLISH
Sighting
For straight cuts, align the 0° position on the front of the
` >I
45° position with it.
W
Fig.15:
1.
K!="
2.
Cutting line
!>I"
Lighting the lamp
CAUTION:
Do not look in the light or see the
source of light directly.
To turn on the lamp without running the tool, pull the
switch trigger without pressing the lock-off button.
To turn on the lamp with the tool running, press and hold
the lock-off button and pull the switch trigger.
The lamp goes out 10 seconds after releasing the switch trigger.
W
Fig.16:
1.
Lamp
NOTE:
$
the lamp. Be careful not to scratch the lens of lamp, or
Hook
Optional accessory
CAUTION:
Always remove the battery when
hanging the tool with the hook.
CAUTION:
Never hook the tool at high loca-
tions or on the surfaces where the tool may lose
the balance and fall.
CAUTION:
Do not pull the tool downward
when it is hooked.
&
W
Fig.17
Attach the hook with the screws as illustrated.
W
Fig.18:
1.
Hook
2.
Screw
& &
the open position.
' &
the closed position.
W
Fig.19:
1.
Open position
2.
Closed position
Electric brake
This tool is equipped with an electric blade brake. If the tool con-
j&
lever release, have tool serviced at a Makita service center.
CAUTION:
The blade brake system is not a
substitute for blade guard. NEVER USE TOOL
WITHOUT A FUNCTIONING BLADE GUARD.
SERIOUS PERSONAL INJURY CAN RESULT.
Electronic function
j
!"
Soft start feature
Soft start because of suppressed starting shock.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Hex wrench storage
' @
&
W
Fig.20:
1.
Hex wrench
Removing or installing circular saw
blade
CAUTION:
Be sure the circular saw blade is
installed with teeth pointing up at the front of the
tool.
CAUTION:
Use only the Makita wrench to
install or remove the circular saw blade.
To remove the circular saw blade, press the shaft lock
use the hex wrench to loosen the hex bolt. Then remove
@
! "
W
Fig.21:
1.
Shaft lock
2.
Hex wrench
3.
Loosen
4.
Tighten
For tool without the ring
W
Fig.22:
1.
Hex bolt
2.
3.
Circular saw
blade
4.
[
For tool with the ring
W
Fig.23:
1.
Hex bolt
2.
3.
Circular saw
blade
4.
Ring
5.
[
To install the circular saw blade, follow the removal
procedure in reverse.
#!>??''#}$='#
other than 15.88 mm hole-diameter
saw blade
one side of it and a different diameter protrusion on the
other side. Choose a correct side on which protrusion
z
W
Fig.24:
1.
Mounting shaft
2.
[
3.
Circular
saw blade
4.
5.
Hex bolt
WARNING:
BE SURE TO TIGHTEN THE HEX
BOLT CLOCKWISE SECURELY. Also be careful
not to tighten the bolt forcibly. Slipping your hand
from the hex wrench can cause a personal injury.
WARNING:
Make sure that the protrusion "a"
?''#}$='?$&'%"%'+
into the saw blade hole "a" perfectly.
Mounting the
blade on the wrong side can result in the dangerous
vibration.
Summary of Contents for DHS782ZJ
