17 ENGLISH
#!>??''#}$='#$
15.88 mm hole-diameter saw blade
*"#^&'*+*
z
outward onto the mounting shaft and then place circu-
! "
@
For tool without the ring
W
Fig.25:
1.
Mounting shaft
2.
[
3.
Circular
saw blade
4.
5.
Hex bolt
For tool with the ring
W
Fig.26:
1.
Mounting shaft
2.
[
3.
Circular
saw blade
4.
5.
Hex bolt
6.
Ring
WARNING:
BE SURE TO TIGHTEN THE HEX
BOLT CLOCKWISE SECURELY. Also be careful
not to tighten the bolt forcibly. Slipping your hand
from the hex wrench can cause a personal injury.
WARNING:
If the ring is needed to mount the
blade onto the spindle, always be sure that the
correct ring for the blade's arbor hole you intend
to use is installed between the inner and the outer
}$='_
$
result in the improper mounting of the blade causing
blade movement and severe vibration resulting in
possible loss of control during operation and in seri-
Blade guard cleaning
' &
also clean the upper and lower blade guards of accu-
mulated sawdust as discussed in the Maintenance
section. Such efforts do not replace the need to check
lower guard operation before each use.
Connecting a vacuum cleaner
'
z& K
__
W
Fig.27:
1.
__
2.
Screw
W
Fig.28:
1.
Hose
2.
Vacuum cleaner
OPERATION
' -
priate Makita genuine circular saw blades, following
materials can also be sawed:
• Aluminum
products
} z&
for the correct circular saw blades to be used for the
material to be cut.
Checking blade guard function
Set the bevel angle to 0°, and then retract the lower
Z
—
Z
—
W
Fig.29:
1.
Upper guard
2.
Lower guard
3.
Base
4.
Stopper
5.
Open
6.
Close
[ &
saw dust is accumulated inside of the upper and lower
[
Makita service center.
Cutting operation
CAUTION:
Wear dust mask when performing
cutting operation.
CAUTION:
Be sure to move the tool forward
in a straight line gently.
Forcing or twisting the tool
will result in overheating the motor and dangerous
&&&
NOTE:
'
&(
@ )
as room temperature. Then, the tool can work to its
W
Fig.30
and rear handle. Use both to best grasp the tool. If both hands
Set the base on the workpiece to be cut without the circular
&
move the tool forward over the workpiece surface, keeping it
&
[
&
saw blade and lead to dangerous kickback and possible
}
to stop and then withdraw tool. Realign tool on new cut
line, and start cut again. Attempt to avoid positioning which
@
$
Rip fence (Guide rule)
CAUTION:
Make sure that the rip fence is
securely installed in the correct position before
use.
[
kickback.
W
Fig.31:
1.
}! "
2.
Clamping screw
@ )
against the side of the workpiece and secure it in posi-
tion with the clamping screw on the front of the base. It
also makes repeated cuts of uniform width possible.
Summary of Contents for DHS782ZJ
