Makita DJV182Y1J Instruction Manual Download

Page: 11 / 80

2. Circular cuts (Fig. 25 & 26)

When cutting circles or arcs of 170 mm or less in radius,
install the rip fence as follows.
1. Insert the rip fence into the rectangular hole on the

side of the base with the fence guide facing up. Insert
the circular guide pin through either of the two holes
on the fence guide. Screw the threaded knob onto the
pin to secure the pin.

2. Now slide the rip fence to the desired cutting radius,

and tighten the bolt to secure it in place. Then move
the base all the way forward.

NOTE:

• Always use blades No. B-17, B-18, B-26 or B-27 when

cutting circles or arcs.

Guide rail adapter set (optional
accessory) (Fig. 27)

When cutting parallel and uniform width or cutting straight,
the use of the guide rail and the guide rail adapter will
assure the production of fast and clean cuts.
To install the guide rail adapter, insert the rule bar into the
square hole of the base as far as it goes. Secure the bolt
with the hex wrench securely.

(Fig. 28)

Install the guide rail adapter on the rail of the guide rail.
Insert the rule bar into the square hole of the guide rail
adapter. Put the base to the side of the guide rail, and
secure the bolt securely.

(Fig. 29)

CAUTION:

• Always use blades No. B-8, B-13, B-16, B-17 or 58

when using the guide rail and the guide rail adapter.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to
perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.

If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Jig saw blades
• Hex wrench 4
• Rip fence (guide rule) set
• Guide rail adapter set
• Guide rail set
• Anti-splintering device
• Cover plate
• Dust nozzle assy
• Makita genuine battery and charger

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ from
country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according
to EN62841-2-11:

Model DJV142

Sound pressure level (L

): 78 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Model DJV182

Sound pressure level (L

): 77 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

ENG907-1

• The declared noise emission value(s) has been

measured in accordance with a standard test method
and may be used for comparing one tool with another.

• The declared noise emission value(s) may also be

used in a preliminary assessment of exposure.

WARNING:

• Wear ear protection.
• The noise emission during actual use of the power

tool can differ from the declared value(s)
depending on the ways in which the tool is used
especially what kind of workpiece is processed.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined
according to EN62841-2-11:

Model DJV142

Work mode: cutting boards
Vibration emission (a

h,B

): 7.0 m/s

Uncertainty (K): 1.5 m/s

Work mode: cutting sheet metal
Vibration emission (a

h,M

): 4.0 m/s

Uncertainty (K): 1.5 m/s