14
ENGLISH
4. Place the adjusting plate on the conventional
planer blade, then simply press in the heel of the
adjusting plate flush with the backside of the blade
gauge.
5. Tighten two screws on the adjusting plate while
the adjusting plate being pressed.
►
Fig.11:
1.
Blade gauge
2.
Inside edge of blade
gauge
3.
Conventional planer blade
4.
Blade edge (of conventional planer blade)
5.
Adjusting plate
6.
Screw
7.
Heel
6.
Clean out all chips or foreign matter adhering to
the drum and the conventional planer blade.
7. Slip the heel of the adjusting plate into the drum
groove, then fit the drum plate on it.
►
Fig.12:
1.
Drum groove
2.
Heel
3.
Drum plate
4.
Installation bolt
8. Tighten all the installation bolts evenly and alter
-
nately with the box wrench.
9. Repeat the above procedures for the other con
-
ventional planer blade.
For tool with mini planer blades
1. To remove the mini planer blades from the tool,
loosen the installation bolts one turn with the box
wrench.
►
Fig.13:
1.
Box wrench
2.
Installation bolt
2. Slide and remove the mini planer blade from the
belt side of the tool.
Using the haft of the box wrench makes it easier
and safety.
►
Fig.14:
1.
Haft of the box wrench
2.
Mini planer
blade
3. To install the mini planer blades, clean out all
chips or foreign matter adhering to the drum and
the mini planer blade.
4. Slide the mini planer blade from opposite side of
the belt of the tool.
5. Tighten all the installation bolts evenly and alter
-
nately with the box wrench.
6. Repeat the above procedures for the other mini
planer blade.
To calibrate the relation between the set plate and the
adjusting plate, perform the following procedure.
1. Loosen the installation bolts one turn with the box
wrench, remove the mini planer blades from the
tool first, and then remove the installation bolts.
The drum plate and the set plate with adjusting
plate come off.
2. Loosen the screws one turn on the adjusting plate.
►
Fig.15:
1.
Screw
2.
Adjusting plate
3.
Set plate
3.
Clean out all chips or foreign matter adhering
to the set plate with adjusting plate and the mini
planer blade.
4. Place the mini planer blade on the blade gauge
so that the blade edge is perfectly flush with the
inside edge of the blade gauge.
5. Place the set plate with the adjusting plate, so that
the locating lugs of the set plate align on the rest
of the mini planer blade.
6. Press in the heel of the adjusting plate flush with
the backside of the blade gauge.
7. Tighten two screws on the adjusting plate while
the adjusting plate being pressed.
►
Fig.16:
1.
Blade gauge
2.
Inside edge of blade
gauge
3.
Mini planer blade
4.
Blade
edge (of mini planer blade)
5.
Set plate
6.
Adjusting plate
7.
Screw
8.
Heel
8. Slip the heel of the adjusting plate into the groove
of the drum.
►
Fig.17:
1.
Drum groove
2.
Heel
3.
Drum plate
4.
Installation bolt
9. Screw all the installation bolts with the box
wrench.
Then install the mini planer blade.
Summary of Contents for DKP181Z
