5
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Intended use
The tool is intended for cutting rebar.
Noise
The typical A-weighted noise level determined according
to EN62841-2-8:
Sound pressure level (LpA) : 80.5 dB(A)
Sound power level (LWA) : 90.1 dB(A)
Uncertainty (K) : 3 dB(A)
NOTE:
• The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
• The declared noise emission value(s) may also be
used in a preliminary assessment of exposure.
WARNING:
•
Wear ear protection.
•
The noise emission during actual use of the power
tool can differ from the declared value(s)
depending on the ways in which the tool is used
especially what kind of workpiece is processed.
•
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN62841-2-8:
Work mode : cutting rebar
Vibration emission (a
h
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
NOTE:
• The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
• The declared vibration total value(s) may also be used
in a preliminary assessment of exposure.
WARNING:
•
The vibration emission during actual use of the
power tool can differ from the declared value(s)
depending on the ways in which the tool is used
especially what kind of workpiece is processed.
•
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
General Power Tool Safety
Warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and
instructions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit.
Cluttered or dark
areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool.
Distractions can cause you
to lose control.
..... Read instruction manual.
............... Flying debris and loud noise hazards.
Wear ear and eye protection.
............... Moving blade. Keep hands clear while
machine is operating. Turn power off
before servicing.
........ Only for EU countries
Due to the presence of hazardous
components in the equipment, waste
electrical and electronic equipment,
accumulators and batteries may have a
negative impact on the environment and
human health.
Do not dispose of electrical and
electronic appliances or batteries with
household waste!
In accordance with the European
Directive on waste electrical and
electronic equipment and on
accumulators and batteries and waste
accumulators and batteries, as well as
their adaptation to national law, waste
electrical equipment, batteries and
accumulators should be stored
separately and delivered to a separate
collection point for municipal waste,
operating in accordance with the
regulations on environmental protection.
This is indicated by the symbol of the
crossed-out wheeled bin placed on the
equipment.
Ni-MH
Li-ion
