20 ENGLISH
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
CAUTION:
Clean out the guard to ensure
there is no accumulated sawdust which may
impede the operation of the guarding system.
A
dirty guarding system may limit the proper operation
which could result in serious personal injury. The
most effective way to accomplish this cleaning is with
compressed air.
If the dust is being blown out of
the guard, be sure the proper eye and breathing
protection is used.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Adjusting 0°-cut and 45°-cut
accuracy
NOTICE:
Do not engage the levers for -1° bevel
angle when adjusting 0°-cut accuracy.
NOTICE:
Do not engage the lever for 48° bevel
angle when adjusting 45°-cut accuracy.
These adjustments have been made at the factory.
But if they are off, you can adjust them as the following
procedures.
1.
Slightly loosen the clamping screws on the front
and rear of the tool.
2.
Adjust the blade angle.
►
Fig.45:
1.
Triangular rule
To adjust the 0°-cut accuracy, make the base perpen
-
dicular to the blade using a triangular rule, square rule,
etc. by turning the adjusting bolt.
►
Fig.46:
1.
Adjusting bolt for 0°-cut
To adjust the 45°-cut accuracy, make the base 45° to
the blade using a triangular rule by turning the adjusting
bolt.
►
Fig.47:
1.
Adjusting bolt for 45°-cut
3.
Tighten the clamping screws and make a test cut.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual.
The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard
-
ing these accessories, ask your local Makita Service
Center.
•
Circular saw blade
•
Sub base
•
Hex wrench
•
Guide rail
•
Bevel guide
•
Clamp
•
Sheet
•
Rubber sheet
•
Position sheet
•
Wireless unit (for DSP601)
•
Makita genuine battery and charger
NOTE:
Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
Summary of Contents for DSP600
