9 ENGLISH
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN ISO 11681-2:
Model DUC256
Work mode: cutting wood
Vibration emission (a
h,W
) : 3.2 m/s
2
Uncertainty (K) : 1.5 m/s
2
Model DUC306
Work mode: cutting wood
Vibration emission (a
h,W
) : 3.2 m/s
2
Uncertainty (K) : 1.5 m/s
2
Model DUC356
Work mode: cutting wood
Vibration emission (a
h,W
) : 3.2 m/s
2
Uncertainty (K) : 1.5 m/s
2
Model DUC406
Work mode: cutting wood
Vibration emission (a
h,W
) : 3.2 m/s
2
Uncertainty (K) : 1.5 m/s
2
Model DUC256C
Work mode: cutting wood
Vibration emission (a
h,W
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea
-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING:
Read all safety warnings, instruc
-
tions, illustrations and specifications provided
with this power tool.
Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc
-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Cordless Chain saw safety warnings
1.
Keep all parts of the body away from the saw
chain when the chain saw is operating. Before
you start the chain saw, make sure the saw
chain is not contacting anything.
A moment of
inattention while operating chain saws may cause
entanglement of your clothing or body with the
saw chain.
2.
Always hold the chain saw with your right
hand on the top handle and your left hand on
the front handle.
Holding the chain saw with a
reversed hand configuration increases the risk of
personal injury and should never be done.
3.
Hold the power tool by insulated gripping
surfaces only, because the saw chain may con
-
tact hidden wiring.
Saw chains contacting a "live"
wire may make exposed metal parts of the power
tool "live" and could give the operator an electric
shock.
4.
Wear safety glasses and hearing protection.
Further protective equipment for head, hands,
legs and feet is recommended. Adequate protec-
tive clothing will reduce personal injury by flying
debris or accidental contact with the saw chain.
5.
Always keep proper footing.
6.
When cutting a limb that is under tension be alert
for spring back.
When the tension in the wood fibres is
released the spring loaded limb may strike the operator
and/or throw the chain saw out of control.
7.
Use extreme caution when cutting brush and sap
-
lings.
The slender material may catch the saw chain
and be whipped toward you or pull you off balance.
8.
Carry the chain saw by the front handle with
the chain saw switched off and away from your
body. When transporting or storing the chain
saw always fit the guide bar cover.
Proper
handling of the chain saw will reduce the likelihood
of accidental contact with the moving saw chain.
9.
Follow instructions for lubricating, chain ten
-
sioning and changing accessories.
Improperly
tensioned or lubricated chain may either break or
increase the chance for kickback.
10.
Keep handles dry, clean, and free from oil and
grease.
Greasy, oily handles are slippery causing
loss of control.
11.
Cut wood only. Do not use chain saw for purposes
not intended.
For example: do not use chain saw for
cutting plastic, masonry or non-wood building materi-
als. Use of the chain saw for operations different than
intended could result in a hazardous situation.
12.
Causes and operator prevention of kickback:
Kickback may occur when the nose or tip of the
guide bar touches an object, or when the wood
closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden
reverse reaction, kicking the guide bar up and
back towards the operator. Pinching the saw chain
along the top of the guide bar may push the guide
Summary of Contents for DUC406ZB
