17 ENGLISH
4.
Set the angle of a file to 45°, and grind the upper
blade from 3 directions with the file.
►
Fig.36:
(1)
File
(2)
45°
CAUTION:
Before grinding the shear blades,
make sure that the tool is switched off and the
battery cartridge is removed from the tool.
5.
Place the tool upside down, and then remove the
burrs from the shear blades with the dressing stone.
►
Fig.37:
1.
Dressing stone
6.
Set the angle of the file to 45°, and grind the lower
blade from 3 directions with the file.
7.
Return the tool to normal position, and then
remove the burrs from the shear blades with the dress
-
ing stone.
Grease lubrication
Interval of lubrication:
Every 100 operating hours
1.
Remove the bolt from the hole for lubrication.
►
Fig.38:
1.
Bolt
2.
Remove the cap from the grease vessel. Align the
outlet of the grease vessel with the hole on the cover,
and then press the outlet of the grease vessel onto the
hole.
►
Fig.39:
1.
Grease vessel
2.
Hole
3.
Apply the grease to the tool (Approximately 5 g as
a guide).
4.
Tighten the bolt.
TROUBLESHOOTING
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual,
do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace
-
ment parts for repairs.
State of abnormality
Probable cause (malfunction)
Remedy
Motor does not run.
Battery cartridge is not installed.
Install the battery cartridge.
Battery problem (under voltage)
Recharge the battery. If recharging is not effective,
replace battery.
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Motor stops running after a little use. Battery's charge level is low.
Recharge the battery. If recharging is not effective,
replace battery.
Overheating.
Stop using of tool to allow it to cool down.
Tool does not reach maximum RPM.
Battery is installed improperly.
Install the battery cartridge as described in this
manual.
Battery power is dropping.
Recharge the battery. If recharging is not effective,
replace battery.
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Shear blades do not move:
stop the machine immediately!
Foreign objects are caught between the
shear blades.
1. Use the reverse button.
2. Switch off the tool and remove the battery car
-
tridge, and then remove the foreign objects using
tools such as pliers.
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Abnormal vibration:
stop the machine immediately!
Shear blades are broken, bent or worn. Replace the shear blades.
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Shear blades and motor cannot stop:
Remove the battery immediately!
Electric malfunction.
Remove the battery and ask your local authorized
service center for repair.
Summary of Contents for DUH504S
