16
NOTE:
•
Do not expand the wire guard outward too much.
Otherwise it may break.
Fig.25
When wire guard is not in use, lift it for the idle position.
Installing nylon cutting head
CAUTION:
•
If during operation the nylon cutting head
accidentally impacts a rock or hard object the
trimmer should be stopped and inspected for any
damage. If the nylon cutting head is damaged it
should be replaced immediately.
Use of a damaged
nylon cutting head could result in serious personal injury.
NOTICE:
•
Be sure to use genuine Makita nylon cutting head.
Turn the tool upside down so that you can replace the
nylon cutting head easily.
Fig.26
Insert the hex wrench through the hole on the protector
cover and rotate the receive washer until it is locked
with the hex wrench. The nylon cutting head onto the
threaded spindle directly and tighten it by turning it
counterclockwise. Remove the hex wrench.
To remove the nylon cutting head, turn the nylon cutting
head clockwise while holding the receive washer with
the hex wrench.
Installing the cutter blade (country specific)
WARNING:
•
The outside diameter of the cutter blade must
be 230 mm.
Never use any blade exceeding 230
mm in outside diameter.
CAUTION:
•
The cutter blade must be well polished, free of
cracks or breakage. Polish or replace the cutter
blade every three hours of operation.
•
Always wear gloves when handling the cutter blade.
•
Always attach the blade cover when the tool is not
in use or is being transported.
•
The cutter blade-fastening nut (with spring washer)
wears out in course of time. If there appears any wear
or deformation on the spring washer, replace the nut.
Ask your local authorized service center to order it.
NOTICE:
•
Be sure to use genuine Makita cutter blade.
Turn the tool upside down so that you can replace the
cutter blade easily.
Fig.27
To dismount the cutter blade, insert the hex wrench
through the hole on the protector cover and the gear
case. Rotate the receive washer until it is locked with
the hex wrench. Loosen the hex nut (left-hand thread)
with the socket wrench and remove the nut, clamp
washer and hex wrench.
Fig.28
Mount the cutter blade onto the shaft so that the guide
of the receive washer fits in the arbor hole in the cutter
blade. Install the clamp washer and secure the cutter
blade with the hex nut with 13 to 23 Nm of tightening
torque during holding the receive washer with hex
wrench.
Fig.29
Make sure that the blade is the left way up.
Hex wrench storage
Fig.30
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
OPERATION
Correct handling of tool (DUR361U)
Correct posture
WARNING:
•
Always position the tool on your right-hand side
so that the shaft of the left handle is always in
front of your body.
Correct positioning of the tool
allows for maximum control and will reduce the risk of
serious personal injury caused by kickback.
Fig.31
As shown in the figure fit the shoulder harness and
hang the tool firmly on your right side so that the shaft of
the left handle is always ahead of you.
Attachment of shoulder harness
Fig.32
Wear the shoulder harness on your back and buckle it
up until a click is heard. Make sure that it cannot be
taken off with pulling it off. Hang the tool as shown.
WARNING:
•
Be extremely careful to maintain control of the tool
at this time. Do not allow the tool to be deflected
toward you or anyone in the work vicinity.
Failure
to do so could result in serious injury.
Adjustment of the hanger position and shoulder
harness
When replacing battery or accessories with others, the
weight balance of the tool may change. In such case,
adjust the hanger position and shoulder harness length
as follows.
To change the hanger position, loosen the fixing screw
on the hanger with the supplied wrench and then move
the hanger and the cushion. The cushion can be moved
easily by twisting it.
Fig.33
Adjust the hanger position and shoulder harness length
so that:
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
