background image

4

General precautions

The operator MUST read this instruction manual to ensure safe operation 

 -

(even if you already have experience in using cutoff saws).

 It is important 

to be familiar with the operation of this particular cutoff saw. Users insufficiently 

informed will endanger themselves as well as others due to improper handling.

Let only persons who have experience in using cutoff saws work with this unit. 

 -

When letting another person use the Power Cutter, this instruction manual must 

be provided along with it.

First-time operators should ask a specialist to instruct them in working with 

 -

gasoline-powered cutoff saws.

Children and persons under 18 years of age must not be allowed to use this 

 -

Power Cutter. Persons over the age of 16 years may, however, use the Power 

Cutter for the purpose of being trained as long as they are under the supervision 

of a qualified trainer.

Working with the Power Cutter requires high concentration.

 -

Operate the Power Cutter only if you are in good physical condition. If you are 

 -

tired, your attention will be reduced. Be especially careful at the end of a working 

day. Perform all work calmly and carefully. The user has to accept liability for 

others.

Never work while under the influence of alcohol, drugs, medication or other 

 -

substances which may impair vision, dexterity or judgement.

A fire extinguisher must be available in the immediate vicinity.

 -

Asbestos and other materials that can release toxins may be cut only with the 

 -

necessary safety precautions and after notification of the proper authorities and 

under their supervision or that of a person appointed by them.

Protective equipment

In order to avoid head, eye, hand or foot injuries as well as to protect your 

 -

hearing the following protective equipment must be used during operation 

of the Power Cutter:

The kind of clothing should be appropriate, i. e. it should be tight-fitting but not 

 -

be a hindrance. Clothing in which grains of material can accumulate (trousers 

with cuffs, jackets and trousers with wide-open pockets, etc.) must not be worn, 

particularly when cutting metal.

Do not wear any jewellery or clothing that can get caught or distract from the 

 -

operation of the Power Cutter.

It is necessary to wear a protective helmet whenever working with the Power 

 -

Cutter. The 

protective helmet 

(A) is to be checked in regular intervals for 

damage and is to be replaced after 5 years at the latest. Use only approved 

protective helmets.

The helmet 

 -

visor

 (B) protects the face from dust and material grains. In order to 

prevent injuries to eyes and face, always wear 

protective goggles

 (C) or visor 

when using the Power Cutter.

To prevent hearing damage, always wear suitable personal 

 -

hearing protection

 

(ear muffs (D), ear plugs, etc.). Octave brand analysis upon request.

When dry-cutting dust-producing materials such as stone or concrete, always 

 -

wear approved 

respiratory protection

 (E).

Work gloves

 -

 (F) of tough leather are part of the required work kit of the Power 

Cutter and must always be worn when working with the Power Cutter.

SAFETY PRECAUTIONS

E

F

1

2

3

4

Summary of Contents for EK7650H





























Reviews: