background image

P 1

0

/ 1

2

R

epair

[3] DISASSEMBLY/ASSEMBLY

[3] -8. Shaft Lock

DISASSEMBLING

While applying 1R268 to Shoulder pin 6 through the small hole 

on Pin cap, tap 1R268 with a hammer.

Now, Shoulder pin 6 comes out from Gear housing complete.

Release 1R268 from Pin cap carefully

so that Pin cap is not slung by 

Compression spring 8.

Shoulder pin 6

Pin cap

Note

: Do not re-use removed Pin cap

          because removal one damages 

          the inside surface of the cap, 

          producing plastic dust.

Pin cap

Pin cap

Compression

spring 8

1R268

1R350

Fig. 14

Fig. 15

(1) Disassemble Bearing box section from Gear housing. (Refer to 

Fig. 6

)

(2) Disassemble Shaft lock mechanism as drawn in 

Figs. 14

 and 

15

.

Fig. 16

Fig. 17

(1) Be sure to use a new Pin cap for replacement and to remove all the plastic dust on Shoulder pin 6.  (

Fig. 16

)

(2) Assemble the Parts for Shaft lock mechanism as drawn in 

Fig. 17

.

Plastic dust

O Ring 7

Shoulder pin 5

Shoulder

pin 6

Pin cap

Compression

spring 8

ASSEMBLING

2. Assemble new Pin cap by pressing

    it to Shoulder pin 6.

    Note

: Do not forget to assemble 

               Compression spring 8.

1. Insert Shoulder pin 6 through

    the hole of Gear housing 

    complete.

Summary of Contents for GA4042C













Reviews: