7 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
HM001G
Blows per minute
0 - 2,650 min
-1
Rated voltage
D.C. 36 V - 40 V max
Overall length
with BL4025
481 mm
with BL4040
496 mm
Net weight
6.3 - 7.1 kg
•
Due to our continuing program of research and development, the specifications herein are subject to change without notice.
•
Specifications may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi
-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL4020 / BL4025 / BL4040* / BL4050F*
* : Recommended battery
Charger
DC40RA / DC40RB / DC40RC
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Recommended cord connected power source
Portable power pack
PDC01 / PDC1200
•
The cord connected power source(s) listed above may not be available depending on your region of residence.
•
Before using the cord connected power source, read instruction and cautionary markings on them.
Intended use
The tool is intended for chiselling work in concrete,
brick, stone and asphalt as well as for driving and com
-
pacting with appropriate accessories.
Noise
The typical A-weighted noise level determined accord
-
ing to EN60745-2-6:
Sound pressure level (L
pA
) : 89 dB(A)
Sound power level (L
WA
) : 100 dB (A)
Uncertainty (K) : 3 dB(A)
NOTE:
The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima
-
tion of exposure in the actual conditions of use (tak
-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter
-
mined according to EN60745-2-6:
Work mode: chiselling function with side grip
Vibration emission (a
h, Cheq
): 5.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
Work mode: chiselling function with side handle
Vibration emission (a
h, Cheq
): 6.0 m/s
2
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
Summary of Contents for HM001G
