Makita HM1213C Technical Information Download

Page: 4 / 17

Pressing down Flat washer 30 with
1R363, remove Ring spring 26
using 1R003 with 1R212.

While pressing down Spring guide,
remove two Tool retainers.

Remove Flat washer 30, Chuck cover
Rubber ring 30, Chuck ring and
Release cover.

1R363

1R003

Flat washer 30

Chuck cover

Rubber ring 30

Chuck ring

Chuck cover

Ring
spring 26

Flat washer 30

1R212

Release
cover

Fig. 5

Spring guide

Tool retainer (2pcs.)

(2) After removing ring spring 26, disassemble the components of Chuck mechanism.
Tool retainers can be removed from Tool holders as illustrated in

Fig

(1) Remove Handle section as illustrated in

Fig. 4

Remove six 5x25 Tapping screws.
Disconnect Connector of Switch from Controller.
Separate Handle section (Handle base, Switch,
Power supply cord, Handle, Handle cover.)

For easy and safety disassembling, stand the machine
on Work bench as illustrated below.
And remove Tool holder cap with slotted screwdriver.

[3] ASSEMBLY/ DISASSEMBLY
[3]-1. Chuck

DISASSEMBLING

Controller

Connector

5x25 Tapping
screw (6pcs.)

Handle section

Fig. 4

Tool holder cap

Chuck cover

Change
ring cover

/ 1

epair

Summary of Contents for HM1213C


















Search results

Summary of Contents for HM1213C

Reviews:

Related manuals for HM1213C

Brands by name

Popular brands

Makita HM1213C, Technical Information

Search results

Summary of Contents for HM1213C

Reviews:

Related manuals for HM1213C

Brands by name

Popular brands