Makita HPR2410 Instructional Manual Download | Manualshive

Page: 11 / 16

background image

11

ACCESSORIES

CAUTION:

•

These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The
use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.

If you need any assistance for more details regarding these
accessories, ask your local Makita service center.

•

SDS-Plus Carbide-tipped bits

•

SDS to A-Taper adapter

•

Cotter (Drift key)

•

Drill chuck assembly

•

Drill chuck S13

•

Chuck adapter

•

Chuck key S13

•

Bit grease

•

Grip assembly

•

Depth gauge

•

Blow-out bulb

•

Dust cup

•

Dust extractor attachment

•

Safety goggles

•

Plastic carrying case

«
...
9
10
11
12
13
...
»

Summary of Contents for HPR2410

















Reviews:

No comments

Related manuals for HPR2410

Brand: Worx Professional Pages: 118

Brand: Sealey Pages: 3

Brand: Yamato Pages: 19

Brand: Festool Pages: 38

Brand: Far Tools Pages: 46

Brand: jcb Pages: 21

Brand: Skil Pages: 116

Brand: YATO Pages: 88

Brand: Urrea Pages: 16

Brand: Silver Eagle Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands