5 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model
HR3200C
HR3210C
HR3210FCT
Capacities
Concrete
Tungsten-carbide
tipped bit
32 mm
Core bit
90 mm
Steel
13 mm
Wood
32 mm
No load speed (min
-1
)
315 - 630
Blows per minute
1,650 - 3,300
Overall length
398 mm
424 mm
Net weight
4.8 kg
5.2 kg
5.4 kg
Safety class
/II
• Due to our continuing programme of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for hammer drilling in brick, con-
crete and stone as well as for chiselling work.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
Noise
The typical A-weighted noise level determined accord
-
ing to EN60745:
Model HR3200C,HR3210C
Sound pressure level (L
pA
) : 89 dB (A)
Sound power level (L
WA
) : 100 dB (A)
Uncertainty (K) : 3 dB (A)
Model HR3210FCT
Sound pressure level (L
pA
) : 88 dB (A)
Sound power level (L
WA
) : 99 dB (A)
Uncertainty (K) : 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN60745:
Model HR3200C
Work mode : hammer drilling into concrete
Vibration emission (a
h,HD
) : 18.0 m/s
2
Uncertainty (K) : 1.5 m/s
2
Work mode : chiselling
Vibration emission (a
h,CHeq
) : 12.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
Work mode: drilling into metal
Vibration emission (a
h,D
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
Model HR3210C
Work mode : hammer drilling into concrete
Vibration emission (a
h,HD
) : 10.0 m/s
2
Uncertainty (K) : 1.5 m/s
2
Work mode : chiselling
Vibration emission (a
h,CHeq
) : 7.5 m/s
2
Uncertainty (K) : 1.5 m/s
2
Work mode: drilling into metal
Vibration emission (a
h,D
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
Model HR3210FCT
Work mode : hammer drilling into concrete
Vibration emission (a
h,HD
) : 10.0 m/s
2
Uncertainty (K) : 1.5 m/s
2
Work mode : chiselling
Vibration emission (a
h,CHeq
) : 8.0 m/s
2
Uncertainty (K) : 1.5 m/s
2
Work mode: drilling into metal
Vibration emission (a
h,D
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
Summary of Contents for HR3200C
