Makita HR5001C Technical Information Download

Page: 3 / 12

Repair

(1) Removing Change lever ------------------------------ ------(Page 6 of 14)

(2) Install Change lever ------------------------------- ----------(Page 6 of 14)

(3) Replace the Armature ------------------------------- --------(Page 7 of 14)

(4) Disassembling the chuck --------------------------- -------(Page 8 of 14)

(5) Assembling the chuck ------------------------------- -------(Page 8 of 14)

(6) Removing Tool holderers --------------------------- ------(Page 8 of 14)

(7) Disassembling tool holders ------------------------- -------(Page 9 of 14)

(8) Assembling the tool holder A and B ----------------- -----(Page 9 of 14)

(9) Taking out Cylinder 40 ----------------------------- --------(Page 9 of 14)

(10) Assembling Piston, Rod and Crank shaft -------------- -(Page 10 of 14)

(11) Assembling Fluoride ring 28 on Impact bolt ---------- (Page 10 of 14)

(12) Assembling several parts in Crank housing ----------- (Page 11 of 14)

(13) Inserting T ool holders -------------------------------------(Page 11 of 14)

(14) Assembling Torque limiter complete ------------------ -(Page 12 of 14)

(15) Lublication ----------------------------------------- --------(Page 13 of 14)

Summary of Contents for HR5001C












