10 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
HS011G
Blade diameter
255 mm
260 mm
270 mm
Max. Cutting depth
at 0°
94 mm
97 mm
101 mm
at 45° bevel
65 mm
68 mm
71 mm
at 60° bevel
45 mm
48 mm
51 mm
No load speed
3,500 min
-1
Overall length
453 mm
Rated voltage
D.C. 36 V - 40 V max
Net weight
5.5 - 6.7 kg
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications and battery cartridge may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi
-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL4020 / BL4025 / BL4040 / BL4050F* / BL4080F*
* : Recommended battery
Charger
DC40RA / DC40RB / DC40RC
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece.
Noise
The typical A-weighted noise level determined accord
-
ing to EN62841-2-5:
Sound pressure level (L
pA
) : 93 dB(A)
Sound power level (L
WA
) : 104 dB (A)
Uncertainty (K) : 3 dB(A)
NOTE:
The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter
-
mined according to EN62841-2-5:
Work mode: cutting wood
Vibration emission (a
h,W
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
Summary of Contents for HS011G
