19 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
LS004G
Blade diameter
European countries
260 mm
Countries other than Europe
255 mm - 260 mm
Hole diameter
European countries
30 mm
Countries other than Europe
(country specific)
15.88 mm / 25.4 mm / 30 mm
Max. kerf thickness of the saw blade
3.2 mm
Max. miter angle
Right 60°, Left 60°
Max. bevel angle
Right 48°, Left 48°
No load speed (RPM)
3,600 min
-1
Dimensions (L x W x H)
805 mm x 644 mm x 660 mm
Rated voltage
D.C. 36 V - 40 V max
Net weight
26.6 - 27.2 kg
Cutting capacities (H x W)
Miter angle
Bevel angle
45° (left)
0°
45° (right)
0°
42 mm x 310 mm
58 mm x 279 mm
68 mm x 310 mm
91 mm x 279 mm
29 mm x 310 mm
43 mm x 279 mm
45° (right and left)
42 mm x 218 mm
58 mm x 197 mm
68 mm x 218 mm
91 mm x 197 mm
29 mm x 218 mm
43 mm x 197 mm
60° (right and left)
-
68 mm x 155 mm
91 mm x 139 mm
-
Cutting capacities for special cuttings
Type of cutting
Cutting capacity
Crown molding 45° type
(with crown molding stopper used)
168 mm
Base board
(with horizontal vise used)
133 mm
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi
-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL4020 / BL4025 / BL4040* / BL4050F*
* : Recommended battery
Charger
DC40RA / DC40RB / DC40RC
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Summary of Contents for LS004GZ01
