35 ENGLISH
Groove cutting
WARNING:
Do not attempt to perform this
type of cut by using a wider type blade or dado
blade.
Attempting to make a groove cut with a wider
blade or dado blade could lead to unexpected cutting
results and kickback which may result in serious
personal injury.
WARNING:
Be sure to return the stopper arm
to the original position when performing other
than groove cutting.
Attempting to make cuts with
the stopper arm in the incorrect position could lead to
unexpected cutting results and kickback which may
result in serious personal injury.
For a dado type cut, perform as follows:
1.
Adjust the lower limit position of the circular saw
blade using the adjusting screw and the stopper arm to
limit the cutting depth of the circular saw blade. Refer to
the section for stopper arm.
2.
After adjusting the lower limit position of the circu
-
lar saw blade, cut parallel grooves across the width of
the workpiece using a slide (push) cut.
►
Fig.68:
1.
Cut grooves with blade
3.
Remove the workpiece material between the
grooves with a chisel.
Carrying tool
Before carrying the tool, be sure to remove the battery
cartridge and all movable parts of the miter saw are
secured. Always check the following:
•
The battery cartridge is removed.
•
The carriage is at 0° bevel angle position and
secured.
•
The carriage is lowered and locked.
•
The carriage is fully slid to the guide fences and
locked.
•
The turn base is at the full right miter angle posi-
tion and secured.
•
The holders are stored and secured.
Carry the tool by holding both sides of the tool base.
►
Fig.69
WARNING:
Stopper pin for carriage elevation
is for carrying and storage purposes only and not
for any cutting operations.
The use of the stopper
pin for cutting operations may cause unexpected
movement of the circular saw blade resulting in kick-
back and serious personal injury.
CAUTION:
Always secure all moving portions
before carrying the tool.
If portions of the tool move
or slide while being carried, loss of control or balance
may occur and result in personal injury.
CAUTION:
Be sure that the carriage elevation
is properly locked at its bottom by the stopper
pin.
If the stopper pin is not engaged properly, the
carriage may jump up suddenly and cause personal
injury.
WIRELESS ACTIVATION
FUNCTION
What you can do with the wireless
activation function
The wireless activation function enables clean and com-
fortable operation. By connecting a supported vacuum
cleaner to the tool, you can run the vacuum cleaner
automatically along with the switch operation of the tool.
►
Fig.70
To use the wireless activation function, prepare following items:
•
A wireless unit (optional accessory)
•
A vacuum cleaner which supports the wireless
activation function
The overview of the wireless activation function setting is
as follows. Refer to each section for detail procedures.
1.
Installing the wireless unit
2.
Tool registration for the vacuum cleaner
3.
Starting the wireless activation function
Installing the wireless unit
Optional accessory
CAUTION:
Place the tool on a flat and stable
surface when installing the wireless unit.
NOTICE:
Clean the dust and dirt on the tool
before installing the wireless unit.
Dust or dirt
may cause malfunction if it comes into the slot of the
wireless unit.
NOTICE:
To prevent the malfunction caused by
static, touch a static discharging material, such
as a metal part of the tool, before picking up the
wireless unit.
NOTICE:
When installing the wireless unit,
always be sure that the wireless unit is inserted
in the correct direction and the lid is completely
closed.
1.
Open the lid on the tool as shown in the figure.
►
Fig.71:
1.
Lid
2.
Insert the wireless unit to the slot and then close the lid.
When inserting the wireless unit, align the projections
with the recessed portions on the slot.
►
Fig.72:
1.
Wireless unit
2.
Projection
3.
Lid
4.
Recessed portion
When removing the wireless unit, open the lid slowly.
The hooks on the back of the lid will lift the wireless unit
as you pull up the lid.
►
Fig.73:
1.
Wireless unit
2.
Hook
3.
Lid
After removing the wireless unit, keep it in the supplied
case or a static-free container.
NOTICE:
Always use the hooks on the back of
the lid when removing the wireless unit.
If the
hooks do not catch the wireless unit, close the lid
completely and open it slowly again.
Summary of Contents for LS004GZ01
