Makita LS1040F Instructions Manual Download

Page: 12 / 104

For all countries other than European countries
(Fig. 14)

To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided.
To start the tool, depress the lock-off button and pull the
switch trigger. Release the switch trigger to stop.

WARNING:
• NEVER use tool without a fully operative switch trigger.

Any tool with an inoperative switch is HIGHLY DAN-
GEROUS and must be repaired before further usage.

• For your safety, this tool is equipped with a lock-off but-

ton which prevents the tool from unintended starting.
NEVER use the tool if it runs when you simply pull the
switch trigger without pressing the lock-off button.
Return tool to a Makita service center for proper repairs
BEFORE further usage.

• NEVER tape down or defeat purpose and function of

lock-off button.

Lighting up the lamps

(Fig. 15, 16)

CAUTION:
• This is not a rainproof light. Do not wash the light in

water or use it in a rain or a wet area. Such a conduct
can cause an electric shock and fume.

• Do not touch the lens of the light, as it is very hot while

it is lighted or shortly after it is turned off. This may
cause a burn to a human body.

• Do not apply impact to the light, which may cause dam-

age or shorted service time to it.

• Do not keep casting the beam of the light to your eyes.

This can cause your eyes to be hurt.

• Do not cover the light with clothes, carton, cardboard or

similar objects while it is lighted, which can cause a fire
or an ignition.

Push the upper position of the switch for turning on the
light and the lower position for off.

Move the light to shift an area of lighting.

NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of light, or it may lower
the illumination.

ASSEMBLY

CAUTION:
• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing saw blade

CAUTION:
• Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

• Use only the Makita socket wrench provided to install

or remove the blade. Failure to do so may result in
overtightening or insufficient tightening of the hex bolt.
This could cause a personal injury.

To remove the blade, use the socket wrench to loosen
the hex bolt holding the center cover by turning it coun-
terclockwise. Raise the blade guard and center cover.

(Fig. 17)

Press the shaft lock to lock the spindle and use the
socket wrench to loosen the hex bolt clockwise. Then
remove the hex bolt, outer flange and blade.

(Fig. 18)

To install the blade, mount it carefully onto the spindle,
making sure that the direction of the arrow on the surface
of the blade matches the direction of the arrow on the
blade case. Install the outer flange and hex bolt, and then
use the socket wrench to tighten the hex bolt (left-
handed) securely counterclockwise while pressing the
shaft lock.

(Fig. 19)

CAUTION:

For all countries other than European countries

• The silver ring 25.4 mm in outer diameter is factory-

installed onto the spindle. The black ring 25 mm in
outer diameter is included as standard equipment.
Before mounting the blade onto the spindle, always be
sure that the correct ring for the arbor hole of the blade
you intend to use is installed onto the spindle.

For European countries

• The ring 30 mm in outer diameter is factory-installed

onto the spindle.

Install the flange and hex bolt, and then use the socket
wrench to tighten the hex bolt securely counterclockwise
while pressing the shaft lock.

Return the blade guard and center cover to its original
position. Then tighten the hex bolt clockwise to secure
the center cover. Lower the handle to make sure that the
blade guard moves properly. Make sure shaft lock has
released spindle before making cut.

(Fig. 20)

Dust bag

(Fig. 21)

The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, fit it onto
the dust nozzle.

When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust
bag of its contents, tapping it lightly so as to remove par-
ticles adhering to the insides which might hamper further
collection.

NOTE:
• If you connect a Makita vacuum cleaner to this tool,

more efficient and cleaner operations can be per-
formed.

Securing workpiece

(Fig. 22)

WARNING:
• It is extremely important to always secure the work-

piece properly and tightly with the vise. Failure to do so
can cause the tool to be damaged and/or the work-
piece to be destroyed. PERSONAL INJURY MAY
ALSO RESULT. Also, after a cutting operation, DO
NOT raise the blade until the blade has come to a com-
plete stop.

CAUTION:
• When cutting long workpieces, use supports that are

as high as the top surface level of the turn base. Do not
rely solely on the vertical vise and/ or horizontal vise to
secure the workpiece.
Thin material tends to sag. Support workpiece over its
entire length to avoid blade pinch and possible KICK-
BACK.