5 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
TW001G
Fastening capacities
Standard bolt
M12 - M36
High tensile bolt
M10 - M27
Square drive
19.0 mm
No load speed (RPM)
Max impact mode (4)
0 - 1,800 min
-1
Hard impact mode (3)
0 - 1,400 min
-1
Medium impact mode (2)
0 - 1,150 min
-1
Soft impact mode (1)
0 - 950 min
-1
Impacts per minute
Max impact mode (4)
0 - 2,500 min
-1
Hard impact mode (3)
0 - 2,400 min
-1
Medium impact mode (2)
0 - 2,200 min
-1
Soft impact mode (1)
0 - 1,900 min
-1
Max. fastening torque
(at max impact mode (4) )
Fastening with M30 for 6 seconds
1,800 N·m
Fastening with M30 for 3 seconds
1,500 N·m
Nut-Busting torque
(at max impact mode (4) )
2,050 N·m
Overall length
217 mm
Rated voltage
D.C. 36 V - 40 V max
Net weight
3.9 - 5.1 kg
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi
-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL4020* / BL4025* / BL4040* / BL4050F / BL4080F
* : Recommended battery
Charger
DC40RA / DC40RB / DC40RC
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for fastening bolts and nuts.
Noise
The typical A-weighted noise level determined accord
-
ing to EN62841-2-2:
Sound pressure level (L
pA
) : 100 dB (A)
Sound power level (L
WA
) : 111 dB (A)
Uncertainty (K) : 3 dB (A)
NOTE:
The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Summary of Contents for TW001GD201
