4 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
TW161D
Fastening capacities
Standard bolt
M8 - M16
High tensile bolt
M6 - M12
Square drive
12.7 mm
No load speed
Hard impact mode
0 - 2,400 min
-1
Soft impact mode
0 - 1,300 min
-1
Impacts per minute
Hard impact mode
0 - 3,600 min
-1
Soft impact mode
0 - 2,000 min
-1
Overall length
150 mm
Rated voltage
D.C. 10.8 V - 12 V max
Net weight
1.0 - 1.2 kg
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi
-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL1015 / BL1016 / BL1020B / BL1021B / BL1040B / BL1041B
Charger
DC10SA / DC10SB / DC10WC / DC10WD / DC18RE
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for fastening bolts and nuts.
Noise
The typical A-weighted noise level determined accord
-
ing to EN62841-2-2:
Sound pressure level (L
pA
) : 93 dB(A)
Sound power level (L
WA
) : 104 dB (A)
Uncertainty (K) : 3 dB(A)
NOTE:
The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima
-
tion of exposure in the actual conditions of use (tak
-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter
-
mined according to EN62841-2-2:
Work mode: impact tightening of fasteners of the maxi-
mum capacity of the tool
Vibration emission (a
h
) : 8.0 m/s
2
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE:
The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
Summary of Contents for TW161DZ
