11
3. To avoid kickback:
− Apply the segment between 8 and 11 o’clock.
− Never apply the segment between 12 and 2
o’clock.
− Never apply the segment between 11 and 12
o’clock and between 2 and 5 o’clock, unless the
operator is well trained and experienced and
does it at his/her own risk.
− Never use cutting blades close to solids, such as
fences, walls, tree trunks and stones.
− Never use cutting blades vertically, for such
operations as edging and trimming hedges.
Vibration
1. People with poor circulation who are exposed to
excessive vibration may experience injury to blood
vessels or the nervous system. Vibration may cause
the following symptoms to occur in the fingers, hands
or wrists: “Falling asleep” (numbness), tingling,
pain, stabbing sensation, alteration of skin color or
of the skin. If any of these symptoms occur, see a
physician!
2. To reduce the risk of “white finger disease”, keep
your hands warm during operation and well maintain
the tool and accessories.
Transport
1. Before transporting the tool, turn it off and withdraw
the mains plug. Attach the cover to the cutting
blade.
2. When transporting the tool, carry it in a horizontal
position by holding the shaft.
3. When transporting the tool in a vehicle, properly
secure it to avoid turnover. Otherwise damage to the
tool and other baggage may result.
Maintenance
1. Have your tool serviced by our authorized service
center, always using only genuine replacement
parts. Incorrect repair and poor maintenance can
shorten the life of the tool and increase the risk of
accidents.
2. Before doing any maintenance or repair work or
cleaning the tool, always turn it off and withdraw the
mains plug.
3. Always wear protective gloves when handling the
cutting blade.
4. Always clean dust and dirt off the tool. Never use
gasoline, benzine, thinner, alcohol or the like for the
purpose. Discoloration, deformation or cracks of the
plastic components may result.
5. After each use, tighten all screws and nuts.
6. Do not attempt any maintenance or repair not
described in the instruction manual. Ask our
authorized service center for such work.
7. Always use our genuine spare parts and accessories
only. Using parts or accessories supplied by a third
party may result in the tool breakdown, property
damage and/or serious injury.
8. Request our authorized service center to inspect and
maintain the tool at regular interval.
Storage
1. Before storing the tool, perform full cleaning and
maintenance. Withdraw the mains plug. Attach the
cover to the cutting blade.
2. Store the tool in a dry and high or locked location out
of reach of children.
3. Do not prop the tool against something, such as a
wall. Otherwise it may fall suddenly and cause an
injury.
First aid
1. Always have a first-aid kit close by. Immediately
replace any item taken from the first aid kit.
2. When asking for help, give the following information:
− Place of the accident
− What happened
− Number of injured persons
− Nature of the injury
− Your name
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure
to follow the safety rules stated in this instruction
manual may cause serious personal injury.
PARTS DESCRIPTION (Fig. 1)
FUNCTIONAL DESCRIPTION
WARNING:
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking the
functions on the tool.
Failure to switch off and unplug
may result in serious personal injury from accidental
start-up.
Power switch action (Fig. 2)
WARNING:
•
Before plugging in, always check to see that the
switch trigger actuates properly and returns to
the “OFF” position when released. Do not pull the
switch trigger hard without sliding the lock-off
lever. This can cause switch breakage.
Operating a
tool with a switch that does not actuate properly can
lead to loss of control and serious personal injury.
To prevent the switch trigger from being accidentally
pulled, a lock-off lever is provided.
To start the tool, slide the lock-off lever forward and then
pull the switch trigger. Release the switch trigger to stop.
