background image

9 ENGLISH

Storage

The hook hole on the bottom of the machine is conve-

nient for hanging the machine from a nail or screw on 

the wall. Store the machine in a place out of the reach 

of children and not exposed to moisture or rain.

1

►  

1.

 Hole

TROUBLESHOOTING

Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the man

-

ual, do not attempt to dismantle the machine. Instead, ask Makita Authorized Service Centers, always using Makita 

replacement parts for repairs.

State of abnormality

Probable cause (malfunction)

Remedy

Motor does not run.

Battery cartridge is not installed.

Install the battery cartridge.

Battery problem (under voltage)

Recharge the battery. If recharging is not effective, 

replace battery.

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Motor stops running after a little use.

Battery's charge level is low.

Recharge the battery. If recharging is not effective, 

replace battery.

Overheating.

Stop using the machine to allow it to cool down.

The machine does not reach the 

maximum speed.

Battery is installed improperly.

Install the battery cartridge as described in this 

manual.

Battery power is dropping.

Recharge the battery. If recharging is not effective, 

replace battery.

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Abnormal vibration:

 

 stop the machine immediately!

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Motor cannot stop:

 

 Remove the battery immediately!

Electric or electronic malfunction.

Remove the battery and ask your local authorized 

service center for repair.

Summary of Contents for XBU03Z











Reviews: