10
For tool with locking screw type wheel guard
1
2
3
015303
Mount the wheel guard with the protrusions on the
wheel guard band aligned with the notches on the
bearing box. Then rotate the wheel guard around 180
ﾟ
counterclockwise. Be sure to tighten the screw securely.
To remove wheel guard, follow the installation
procedure in reverse.
Installing or removing depressed center
wheel or multi disc (optional accessory)
WARNING:
When using a depressed center wheel or multi
disc, the wheel guard must be fitted on the tool so
that the closed side of the guard always points
toward the operator.
Only actuate the shaft lock when the spindle is not
moving.
1
2
3
015088
Mount the inner flange onto the spindle. Fit the
wheel/disc on the inner flange and screw the lock nut
onto the spindle.
1
2
015089
To tighten the lock nut, press the shaft lock firmly so that
the spindle cannot revolve, then use the lock nut wrench
and securely tighten clockwise.
To remove the wheel, follow the installation procedure in
reverse.
Installing or removing abrasive disc
(optional accessory)
1
2
3
015092
Mount the rubber pad onto the spindle. Fit the disc on
the rubber pad and screw the lock nut onto the spindle.
To tighten the lock nut, press the shaft lock firmly so that
the spindle cannot revolve, then use the lock nut wrench
and securely tighten clockwise.
To remove the disc, follow the installation procedure in
reverse.
NOTE:
Use sander accessories specified in this manual.
These must be purchased separately.
OPERATION
WARNING:
It should never be necessary to force the tool. The
weight of the tool applies adequate pressure.
Forcing and excessive pressure could cause
dangerous wheel breakage.
ALWAYS replace wheel if tool is dropped while
grinding.
NEVER bang or hit grinding disc or wheel onto
work.
Avoid
bouncing
and
snagging
the
wheel,
especially when working corners, sharp edges etc.
This can cause loss of control and kickback.
NEVER use tool with wood cutting blades and
other sawblades. Such blades when used on a
grinder frequently kick and cause loss of control
leading to personal injury.
CAUTION:
Never switch on the tool when it is in contact with
the workpiece, it may cause an injury to operator.
Always wear safety goggles or a face shield during
operation.
After operation, always switch off the tool and wait
until the wheel has come to a complete stop
before putting the tool down.
1. Wheel guard
2. Bearing box
3. Screw
1. Sanding lock nut
2. Abrasive disc
3. Rubber pad
1. Lock nut wrench
2. Shaft lock
1. Lock nut
2. Depressed
center wheel
3. Inner flange
Summary of Contents for XDT13
